background image

4

4

ENGLISH

 

 

GENERAL INFORMATION

General Safety Information

This product must be installed by a legally qualified heat-

ing engineer. On completion of the installation, the install-

er must issue the owner with a declaration of conformity 

confirming that the installation has been completed to 

the highest standards in compliance with the instructions 

provided by 

T

 in this instruction manual, and 

that it conforms to all applicable laws and standards.

This product must only be used for the purpose for which 

it is designed and made, as specified by 

T

T

 declines all responsibility, contractual or 

other, for damage to property or injury to persons or ani-

mals caused by improper installation, adjustment, main-

tenance or use.

The room where the boiler is installed must be properly 

ventilated to ensure a sufficient supply of air for correct 

combustion.

If you notice any water leaks, disconnect the boiler from 

the mains electricity supply and shut off the water supply.

In case of water leaks disconnect the equipment from 

the power mains, close the water supply and promptly 

alert Technical Assistance Centre 

T

 or pro-

fessionally qualified personnel.

The boiler must be serviced at least once a year. The 

failure to perform annual maintenance work will void the 

warranty of the equipment.

Periodically check that pressure in the central heating 

circuit, when cold, is approximately 1.5 bar and be-

low the maximum limit specified for the boiler. If this is 

not the case, contact the Technical Assistance Centre 

T

 or professionally qualified personnel.

If the boiler is not going to be used for an extended peri-

od of time, perform the operations described later in this 

manual.

This manual is an integral part of the equipment and 

therefore must be stored carefully and must ALWAYS ac-

company the boiler even if it is sold to another Owner or 

User or transferred to another plant. If it is damaged or 

lost, request another copy from your local Technical As-

sistance Centre 

T

.

Precautions

The operation of any appliance that uses fuel, electrical power 

and water demands that a number of fundamental safety pre-

cautions be respected:

Do not allow children or infirm persons to operate the 

system unsupervised.

It is forbidden to use electrical devices or equipment, 

such as switches, appliances, etc. if there is a smell of 

gas or un-burnt products. If so:

- Ventilate the room, opening doors and windows

- Close the fuel shut-off cock

- Ask for the prompt intervention of the Technical Assis-

tance Centre

Do not touch the boiler while barefoot or wet.

Never pull, disconnect, or twist the electrical cables com-

ing from the appliance even if it is disconnected from the 

mains electricity supply.

Do not obstruct or restrict the vents in the room where 

the boiler is installed. Adequate ventilation is essential for 

correct combustion.

Do not expose the boiler to the elements. It is not de-

signed for use outdoors.

It is prohibited to leave inflammable substances and con-

tainers in the room where the boiler is installed.

Do not dispose of packaging material into the environ-

ment, or leave it within the reach of children, since it can 

become a potential hazard. Dispose of packaging mate-

rial in compliance with applicable legislation.

It is forbidden to operate the boiler without water.

The equipment casing must not be removed by people 

without specific qualification and expertise.

Содержание ACQUAHOME R BLU





















Отзывы: