Thermia iTec Скачать руководство пользователя

Страница: 47 / 52

Error codes

The error codes shown in the table below will be visible in the INDOOR UNIT display whenever an error is detected from the OUTDOOR

UNIT. ALL errors will stop the compressor from running until the error is solved. Some errors are automatically cleared, some needs man-

ual action and some severe errors might even need hardware to be replaced or serviced. Follow the superscript to below the table for

further information.

It takes a minimum of 3 minutes for the compressor to start from a

standstill.

Display

Explanation

Error source

E101

Communication error between the indoor and outdoor unit (when indoor unit cannot receive

signals)

COMM KIT

OUTDOOR UNIT

E109

Communication error due to indoor unit address incomplete

COMM KIT

OUTDOOR UNIT

E111

Modbus communication error (when COMM KIT cannot receive signals)

COMM KIT

OUTDOOR UNIT

E162

EEPROM H/W error

COMM KIT

E177

Emergency error

COMM KIT

OUTDOOR UNIT

E201

COMM KIT/OUTDOOR UNIT communication error (matching error)

OUTDOOR UNIT

E202

COMM KIT/OUTDOOR UNIT communication error (3 min)

OUTDOOR UNIT

E203

Communication error between INVERTER and MAIN MICOM (6 min)

OUTDOOR UNIT

E221

OUTDOOR UNIT temperature sensor error

OUTDOOR UNIT

E231

Condenser temperature sensor error

OUTDOOR UNIT

E251

Discharge temperature sensor error

OUTDOOR UNIT

E320

OLP sensor error

OUTDOOR UNIT

E403

1, 4

Detection of OUTDOOR UNIT compressor freezing (during cooling operation)

OUTDOOR UNIT

E404

1, 4

Protection of OUTDOOR UNIT when it is overload (during Safety start, Normal operation state) OUTDOOR UNIT

E407

1, 4

Comp down due to high pressure

OUTDOOR UNIT

E416

Discharge of compressor is overheated

OUTDOOR UNIT

E425

Power source line missing error (only for 3-phase models)

OUTDOOR UNIT

E440

1, 4

Heating operation blocked (outdoor temperature over 35°C)

OUTDOOR UNIT

E441

1, 4

Cooling operation blocked (outdoor temperature below 9°C)

OUTDOOR UNIT

E458

OUTDOOR UNIT fan 1 error

OUTDOOR UNIT

E461

[Inverter] Compressor startup error

OUTDOOR UNIT

E462

[Inverter] Total current error/PFC over current error

OUTDOOR UNIT

E463

OLP is overheated

OUTDOOR UNIT

E464

[Inverter] IPM over current error

OUTDOOR UNIT

E465

Compressor V limit error

OUTDOOR UNIT

E466

1, 4

DC LINK over/low voltage error

OUTDOOR UNIT

E467

[Inverter] Compressor rotation error

OUTDOOR UNIT

E468

[Inverter] Current sensor error

OUTDOOR UNIT

E469

[Inverter] DC LINK voltage sensor error

OUTDOOR UNIT

E470

Outdoor unit EEPROM Read/Write error

OUTDOOR UNIT

E471

Outdoor unit EEPROM Read/Write error (OTP error)

OUTDOOR UNIT

E474

IPM(IGBT Module) or PFCM temperature sensor error

OUTDOOR UNIT

Commissioning

iTec

Thermia Värmepumpar

VIJSR102

Содержание iTec





















































Результаты поиска

Содержание iTec

Отзывы:

Похожие инструкции для iTec

Бренды по названию

Популярные бренды

Thermia iTec, Пусконаладка

Результаты поиска

Содержание iTec

Отзывы:

Похожие инструкции для iTec

Бренды по названию

Популярные бренды