manualshive.com logo in svg

Thermal Dynamics MERLIN 6000, Руководство по обслуживанию, Страница: 60 / 112

Поделиться
Скачать
Thermal Dynamics MERLIN 6000 Скачать руководство пользователя страница 60

REPLACEMENT PROCEDURES

54

Manual 0-2569

2.  Disconnect the Torch connection to the fitting be-

ing replaced at the Upper Chassis/Gauge Assem-
bly.

3.  Disconnect the gas Hose Assembly from the fitting

at the end of the Gas Input Fitting.

4.  Remove the fitting screwed into the end of the Gas

Input Fitting.

5.  Remove the first nut from the Gas Input Fitting.

6.  Remove the second nut securing the Gas Input Fit-

ting to the Upper Chassis/Gauge Assembly.

7.  Pull the fitting from the Upper Chassis/Gauge As-

sembly.

8.  Reinstall the replacement Plasma or Secondary Gas

Input Fitting Assembly by reversing the above pro-
cedure.

H.  Fuse (F1 and F2) Replacement

1.  Open the hinged cover at the Front Panel torch

leads connection area.

2.  Locate and remove the cap from the fuse holder.

3.  Pull the faulty Fuse from the fuse holder.

4.  Install the replacement Fuse by reversing the above

procedure.

I.  Plasma or Secondary Regulator Assembly

Replacement

NOTE

Both the Plasma and Secondary Regulator Assem-
blies are replaced in the same manner

1.  Remove the Top Panel per Section 5.04-B.

2.  Carefully remove the input and output gas Hose

Assemblies to the Regulator Assembly.

3.  On the Upper Ghassis/Gauge Assembly remove

the securing nut for the Regulator Assembly.

4.  Slide the Regulator Assembly.out of rear of the

Upper Ghassis/Gauge Assembly.

5.  Remove the fittings from the old Regulator Assem-

bly.

6.  Reinstall the replacement Regulator Assembly by

reversing the above procedure.

J.  Control Logic PC Board Assembly

Replacement

1.  Open the front panel access panel cover at the front

of the Power Supply.

2.  Fasten the access cover open with string or rubber

band.

3.  Note where each connector is located on the old

Control Logic PC Board.

4.  Disconnect the three connectors from the old Con-

trol Logic PC Board.

5.  Note the orientation of the old Control Logic PC

Board.

6.  Remove the old Control Logic PC Board.

7.  On the new Control Logic PC Board set the

switches, SW1 through SW5, the same as the old
Control Logic PC Board.

8.  Install the replacement Control Logic PC Board by

reversing the above procedure.

K.  Switching Control PC Board Assembly

Replacement

1.  Remove the Top and Right Side Panels per Section

5.04-B.

2.  Note the orientation of the old Switching Control

PC Board.

3.  Remove the Switching Control PC Board from the

rear of the Upper Chassis/Gauge Panel far enough
to disconnect the wiring connections.

4.  Note where each connector is located on the Switch-

ing Control PC Board.

5.  Disconnect the connectors from the Switching Con-

trol PC Board.

6.  Reconnect the original wiring connectors to the

replacement Switching Control PC Board before
installing the replacement Switching Control PC
Board.

7.  Install the replacement Switching Control PC Board

by reversing the above procedure.

L.  Coolant Check Valve Replacement

1.  Remove the Top Panel per Section 5.04-B.

2.  Disconnect the Hose Assemblies from the fitting

connection at the input end of the Check Valve.

3.  Carefully remove the Check Valve and fittings from

the TORCH COOLANT SUPPLY fitting.

4.  Remove the Fittings from the old Check Valve.

Содержание MERLIN 6000

















































































































Отзывы:

Нет отзывов