Thermal Dynamics 152 CUTMASTER Скачать руководство пользователя | Manualshive

Страница: 16 / 84

background image

CUTMASTER 152

INTRODUCTION 2-2

Manual 0-4987

2.04 Power Supply Specifications

CutMaster 152 Power Supply Specifications

Input Power

208 / 230 VAC (187 - 253 VAC), Single Phase, 60 Hz
230 VAC (187 - 253 VAC), Three Phase, 50/60 Hz
380 VAC (360 - 440 VAC), Three Phase, 50/60 Hz
400 VAC (360 - 440 VAC), Three Phase, 50 Hz
460 VAC (414 - 506 VAC), Single Phase, 60 Hz
460 VAC (414 - 506 VAC), Three Phase, 60 Hz
600 VAC (540 - 630), Three Phase, 60 Hz

Input Power Cable

Power Supply includes input cable.

Output Current

30 - 120 Amps, Continuously Adjustable

Power Supply Gas

Filtering Ability

Particulates to 5 Microns

CutMaster 152 Power Supply Duty Cycle *

Ambient Tempera-

ture

Duty Cycle Ratings @ 40° C (104° F)

Operating Range 0° - 50° C

All Units

Duty Cycle

**60%

80%

100%

Current

120

120

100

IEC

IEC

IEC

DC Voltage

128

128

120

*

NOTE:

The duty cycle will be reduced if the primary input power (AC) is low

or the output voltage (DC) is higher than shown in this chart.

**60% at 208/230V 1 Phase input ONLY

NOTE

IEC Rating is determined as specified by the International Electro-Technical Commission. These specifications

include calculating an output voltage based upon power supply rated current. To facilitate comparison between

power supplies, all manufacturers use this output voltage to determine duty cycle.

Power Supply Dimensions & Weight

Ventilation Clearance Requirements

30.5"

774.7 m

63 lb / 28.6 kg

10.75"

273 mm

16.375"

416 mm

Art # A-08358

6"

150 mm

24"

610 mm

6"

150 mm

6"

150 mm

Art # A-07925_AB

«
...
14
15
16
17
18
...
»

Содержание 152 CUTMASTER





















































































Отзывы:

Нет отзывов

Похожие инструкции для 152 CUTMASTER

Бренд: Abus Страницы: 2

Бренд: FältCom Страницы: 40

Бренд: K-array Страницы: 20

Бренд: Magmaweld Страницы: 8

AZ8350 - Cd Radio Cass Recorder

Бренд: Magnavox Страницы: 18

Бренд: Magmate Страницы: 20

Бренд: Samsung Страницы: 33

Бренд: 1 Sound Страницы: 92

ACUSTICA H series

Бренд: RCF Страницы: 10

ActiveEYE MS15A

Бренд: X10 Страницы: 2

Бренд: Sumner Страницы: 10

Бренд: HySecurity Страницы: 8

GI.BI.DI. FLOOR Series

Бренд: Bandini Industrie Страницы: 19

Бренд: A1 Security Cameras Страницы: 2

Бренд: Q-See Страницы: 9

Бренд: SAKUTUS Страницы: 10

Бренд: Uniden Страницы: 80

Бренд: STAYER WELDING Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды