Thermal Dynamics 152 CUTMASTER Скачать руководство пользователя

Страница: 23 / 84

CUTMASTER 152

Manual 0-4987

3-1 INSTALLATION

SECTION 3 SYSTEM:

INSTALLATION

3.01 Unpacking

1. Use the packing lists to identify and ac-

count for each item.

2. Inspect each item for possible shipping

damage. If damage is evident, contact

your distributor and / or shipping company

before proceeding with the installation.

3. Record Power Supply and Torch model

and serial numbers, purchase date and ven-

dor name, in the information block at the

front of this manual.

3.02 Lifting Options

The Power Supply includes a handle for

hand

lifting only

. Be sure unit is lifted and transported

safely and securely.

WARNING

Do not touch live electrical parts.
Disconnect input power cord before moving unit.

FALLING EQUIPMENT

can cause serious personal

injury and can damage equipment.

HANDLE

is not for mechanical lifting.

• Only persons of adequate physical strength

should lift the unit.

• Lift unit by the handles, using two hands.

Do not use straps for lifting.

• Use optional cart or similar device of ad-

equate capacity to move unit.

• Place unit on a proper skid and secure in

place before transporting with a fork lift or

other vehicle.

3.03 Primary Input Power

Connections

CAUTION

Check your power source for correct voltage

before plugging in or connecting the unit. Check

the Voltage Selector at the rear of the unit for

correct setting before plugging in or connecting

the unit. The primary power source, fuse, and

any extension cords used must conform to local

electrical code and the recommended circuit

protection and wiring requirements as specified

in Section 2.

The following illustration and directions are for

changing phase of the power supply.

Art # A-08493

Input Power Cable Connections

Three-Phase (3ø)

Store copper jumpers on base plate

Single-Phase (1ø) and Jumper Settings

GND

L3
L4

GND

L3
L4

Single and Three Phase Input Power Wiring

NOTE

There are two jumpers used for the single phase

230V setting and none for three phase.

Содержание 152 CUTMASTER





















































































Результаты поиска

Содержание 152 CUTMASTER

Отзывы:

Похожие инструкции для 152 CUTMASTER

Бренды по названию

Популярные бренды

Thermal Dynamics 152 CUTMASTER, Руководство по эксплуатации

Результаты поиска

Содержание 152 CUTMASTER

Отзывы:

Похожие инструкции для 152 CUTMASTER

Бренды по названию

Популярные бренды