Thermador CM301B Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 112

background image

CM Oven Service Manual

Lit. No. 94-30-006B

Page 88

REMOVING THE CONVECTION BAKE ELEMENT

Refer to illustration, below, for the following
steps.
1.

Turn off the electrical power to the oven.

2.

To make servicing easier, remove the oven

door (see Page 99).

3.

Remove the racks from the oven.

4.

Remove the front screws from the left and
right oven rack supports and remove the
supports from the oven liner.

5.

Remove the screws from the convection
baffle and remove the baffle from the back
of the oven liner.

6.

Remove the screws from the convection
bake element bracket and the screw from
the bottom support and pull the element
forward, then disconnect the wires from
the terminals.

7.

Install the new convection bake element
and connect the wires to the terminals.

8.

Reassemble the oven.

WARNING

Turn off the electrical power circuit to the
oven at the main junction box before ser-
vicing this unit.

When you work on the oven, be careful
when handling the sheet metal parts. There
are sharp edges present and you can cut
yourself if you are not careful.

CAUTION

Bracket
Screws

Support

Screw

Bracket

CONVECTION

ELEMENT

Bottom

Support

BACK OF

LINER

Convection Baffle

Top

Screw

Top

Screw

Bottom Screws

CONVECTION FAN

ASSEMBLY NOT SHOWN

«
...
88
89
90
91
92
...
»

Содержание CM301B

















































































































Отзывы:

Нет отзывов

Похожие инструкции для CM301B

Бренд: Russell Hobbs Страницы: 40

Бренд: Ignis Страницы: 50

Бренд: Küppersbusch Страницы: 29

Бренд: Prestige Страницы: 32

Бренд: Garland Страницы: 28

Бренд: EASY FAST Страницы: 80

Бренд: Gaggenau Страницы: 60

Бренд: Dacor Страницы: 6

D90D25ESLRIII-XC

Бренд: Galanz Страницы: 59

Бренд: Philco Страницы: 17

Бренд: Newworld Страницы: 36

Бренд: Fama Страницы: 16

Бренд: JUNO Страницы: 22

Бренд: Blanco Страницы: 26

Бренд: Hotpoint Страницы: 40

Бренд: NEFF Страницы: 68

Бренд: Progress Страницы: 32

Бренд: Maksan Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды