Thermador CM301B Скачать руководство пользователя страница 26

Страница: 26 / 112

CM Oven Service Manual

Lit. No. 94-30-006B

Page 24

REMOVING THE CONTROL PANEL ASSEMBLY,

DISPLAY BOARD, & TOUCH PANEL GLASS

WARNING

CAUTION

Turn off the electrical power going to the
oven before servicing.

When you work on the oven, be careful
when handling the sheet metal parts. There
are sharp edges present and you can cut
yourself if you are not careful.

Turn off the electrical power going to the
oven.

Open the microwave oven door.

To remove the control panel assembly:
a) Remove the four outer black screws

from the bottom of the control panel
assembly.

c) Disconnect the cables from the touch

panel glass filter board connectors.

d) Remove the nine indicated screws from

the control panel plate and lift the plate
off the control panel.

b) Pull the top of the control panel for-

ward and unhook the two ball studs at
the top right and left corners from the
catches.

c) Disconnect the five cables from the con-

trol panel board connectors at P2, P4,
P6, P10, and P11 and remove the assem-
bly.

To remove the display board and touch
panel glass:
a) If not already done, remove the con-

trol panel assembly from the oven (see
Step 3).

b) Place the control panel assembly face-

down on a padded work surface to pre-
vent scratching the finish.

e) Lift the display board off the control

panel.

g) Lift the touch panel glass (with filter

boards) out of the control panel frame.

f) Remove the screws from the mounting

brackets and remove the brackets from
the display board.

Display Board

Touch Panel Glass

4 Black Control Panel Screws

5 Bottom Control Panel Plate Screws

4 Top Control Panel Plate Screws

Cables

Bracket Screws

Содержание CM301B

















































































































Результаты поиска

Содержание CM301B

Отзывы:

Похожие инструкции для CM301B

Бренды по названию

Популярные бренды

Thermador CM301B, Руководство по обслуживанию

Результаты поиска

Содержание CM301B

Отзывы:

Похожие инструкции для CM301B

Бренды по названию

Популярные бренды