Thermador CM301B Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 112

background image

CM Oven Service Manual

Lit. No. 94-30-006B

Page 22

REMOVING THE MAGNETRON, &

MAGNETRON THERMAL CUTOUT

WARNING

CAUTION

Turn off the electrical power going to the
oven before servicing.

When you work on the oven, be careful
when handling the sheet metal parts. There
are sharp edges present and you can cut
yourself if you are not careful.

6.

To remove the magnetron:

a) Disconnect the wires from the two ter-

minals.

b) Remove the two screws from the vent

cover and remove the cover.

1.

Turn off the electrical power going to the
oven.

2.

Pull the oven out of its mounting location
so that you can access the trim and ple-
num covers.

3.

Remove the trim and top plenum covers
from the oven (see Page 10).

4.

CAUTION: DISCHARGE THE HIGH
VOLTAGE MICROWAVE CAPACITOR
WITH A 20,000 OHM, 1- OR 2-WATT
RESISTOR TO CHASSIS GROUND
(SEE PAGE 18) BEFORE WORKING ON
ANY OF THE HIGH VOLTAGE COM-
PONENTS. BE VERY CAREFUL NOT
TO TOUCH THE BARE RESISTOR
LEADS WHEN YOU DISCHARGE THE
CAPACITOR.

5.

Remove the two screws from the magne-
tron fan duct and remove the duct.

c) Remove the mounting screws (two

each) from the left and right waveguide
insulation covers and remove the cov-
ers.

Screw

Screw

Vent Cover

OR-136 &
OR-Filament

OR-Filament

Fan Duct

2 Screws

Screws

Screws

Left Insulation

Cover

Right Insulation

Cover

«
...
22
23
24
25
26
...
»

Содержание CM301B

















































































































Отзывы:

Нет отзывов

Похожие инструкции для CM301B

Бренд: Elenberg Страницы: 22

Бренд: Caple Страницы: 26

Бренд: ZANKER Страницы: 48

Бренд: GASLAND chef Страницы: 20

Бренд: Verona Страницы: 24

Бренд: NEFF Страницы: 32

Бренд: Orava Страницы: 18

Profile Advantium PSB9120DFBB

Бренд: GE Страницы: 40

Бренд: Dawlance Страницы: 24

Бренд: Falcon Страницы: 4

Бренд: Maytag Страницы: 28

Бренд: Asko Страницы: 48

Бренд: Daewoo Страницы: 20

Бренд: Sammic Страницы: 44

B12M42 3FR Series

Бренд: NEFF Страницы: 28

Бренд: Belling Страницы: 24

Бренд: G3 Ferrari Страницы: 24

Бренд: NEFF Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды