background image

1-877-420-1330

 

Quest 185 Cool 

Installation, Operation and Maintenance Instructions

3

www.QuestHydro.com

[email protected]

Safety Precautions

Read the installation, operation and maintenance instructions carefully before installing and operating this device. Proper 

adherence to these instructions is essential to obtain maximum benefit from your 

Quest 185 Cool Dehumidifier.

 

READ AND SAVE THESE INSTRUCTIONS

 

•  The Dehumidifier portion is designed to be installed INDOORS IN A 

SPACE THAT IS PROTECTED FROM RAIN AND FLOODING. 

•  The Condensing unit needs to be protected from the elements (direct 

sunlight, rain, snow, etc.) but can be outdoors.

•  Install the unit with space to access the back or side panels for 

maintenance and service. DO NOT INSTALL UNIT WITH THE 

SERVICE PANELS INACCESSIBLE. 

•  Avoid directing the discharge air at people, or over the water in pool areas. 
•  If used near a pool, spa or water; be certain there is NO chance the unit 

could fall into the water, be splashed and that it is plugged into an outlet 

that is a GROUND FAULT INTERRUPT protected circuit. 

•  DO NOT use the device as a bench or table.

 

•  DO NOT place the device directly on structural members. Provide 

vibration isolation in order to minimize operational vibration and/or noise.

•  A drain pan MUST be placed under the unit if installed above a living area 

or above an area where water leakage could cause damage

•  Never operate a unit with a damaged power cord.  If the power cord is 

damaged it must be replaced by the manufacturer, its service agent, or 

similarly qualified person in order to avoid a hazard.

•  Make all electrical connections in accordance with the current edition of 

the NEC ANSI/NFPA 70 and any national and local codes or ordinances 

that may apply.

•  Do not obstruct the air intake and exhaust.  Maintain a .3 m (1 ft) 

clearance around the air intake and exhaust.

•  This appliance is not intended for use by persons (including children) with 

reduced physical, sensory or mental capabilities, or lack of experience 

and knowledge, unless they have been given supervision or instruction 

concerning use of the appliance by a person responsible for their safety. 

Children should be supervised to ensure that they do not play with the 

appliance.

Содержание 4037391


























Отзывы: