Textron 642211 Скачать руководство пользователя | Manualshive

Страница: 18 / 56

background image

2180

Estate
Series

16

Right side adjustments

(wiring harness and seat rod removed for clarity)

HYDROSTAT ADJUSTMENTS

A turnbuckle-style hydrostat neutral adjustment is
provided.

Neutral:

1.

Support the machine with the rear wheels off the
ground. Use jackstands or equivalent support.
Do not rely only on mechanical or hydraulic jacks.

2.

Move the traction levers out into the neutral lock
position and raise the seat.

3.

Disconnect the seat switch and temporarily
connect the two terminals with jumper wire

J

as

shown.

4.

Start the engine and run at low speed.

5.

Loosen jam nuts

T

at both ends of the

turnbuckle.

6.

Rotate the turnbuckle until the corresponding
wheel stops turning. Lock the turnbuckle jam
nuts. Run the engine up to high idle to check the
adjustment. Readjust if necessary.

7.

Repeat steps 5 and 6 for the opposite side.

8.

Remove the jumper wire and reconnect the seat
switch.

Reverse Return:

1.

Move traction levers out to the neutral lock
position and raise the seat.

2.

Locknut

U

should be run on the bolt as far as it

will go.

3.

Loosen jam nut

Y

. Adjust the clevis yoke by

turning the head of the bolt until the clevis pin just
makes contact with the rear of the slot in the
lever it connects with. Tighten jam nut

Y

.

4.

Repeat steps 2 and 3 for the opposite side.

NOTE:

A slight creep in reverse is acceptable

provided the wheel does not turn and the hydrostat
pump does not whine when the parking brake is on.

ADJUSTMENTS

«
...
16
17
18
19
20
...
»

Содержание 642211

























































Отзывы:

Нет отзывов

Похожие инструкции для 642211

Бренд: Texas Страницы: 16

Бренд: VonHaus Страницы: 20

GLM 40/140 P EASY

Бренд: F.F. Group Страницы: 96

Бренд: MTD Страницы: 40

Бренд: AL-KO Страницы: 304

Бренд: Cub Cadet Страницы: 9

Бренд: Cub Cadet Страницы: 24

Бренд: Viking Страницы: 371

Бренд: Dolmar Страницы: 96

Бренд: Dolmar Страницы: 140

Бренд: Exmark Страницы: 44

Бренд: inventiv Страницы: 78

Бренд: Hyundai power products Страницы: 48

BOB-CAT QUICKCAT 912480

Бренд: Schiller Grounds Care Страницы: 34

Reelmaster 7000

Бренд: Toro Страницы: 315

Бренд: Wolf Garten Страницы: 33

Бренд: GreenWorks Pro Страницы: 44

PowerMax 32 E 4033

Бренд: Gardena Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды