manualshive.com logo in svg

Textron 642211, Установка, Запчасти и Обслуживание

Поделиться
Скачать
Textron 642211 Скачать руководство пользователя страница 21

 2180

Estate
Series

19

POWER UNITS

ENGINES :

Construction:

  Aluminum block with cast-in cast iron

sleeves. Aluminum head.

Configuration:

  4-stroke, vertical shaft, V-twin

cylinder, overhead valve, air-cooled.

DRIVE SYSTEM:

Full hydrostatic pump and wheel motor combination
for independently controlled drive wheels.

Pump: 

 Hydrogear BDP-10A 10cc variable

displacement piston pump.

Motors:

  Parker/Ross 15 cu.in. displacement MB

series. Direct drive 1-1/4” (31.8mm) diameter output
shaft.

Turn Radius:

  0”

OPERATOR PRESENCE
INTERLOCK SYSTEM:

Start:

  The PTO (blades) must be off, traction levers

in neutral lock, and parking brake on for engine to
crank.

Run:  

Operator must be in seat to take parking brake

off, to move traction levers out of the neutral lock
position, or to turn the PTO (blades) on or the engine
will kill. The parking brake must be off for the traction
levers to move out of the neutral lock position.

The operator may leave the seat with the engine
running if the parking brake is on, the PTO (blades) is
off, and the traction levers are in the neutral lock
position. A time delay eliminates annoying engine
cutout from operation over rough terrain.

WEIGHT:

1025 lbs (465 kg)

CONTROLS:

Throttle; choke; power takeoff (PTO) clutch switch;
traction levers; parking brake lever; lift lever.

FUEL SYSTEM:

One tank on each side of operator, each with a
shutoff (1/4 turn). Total capacity 12 gallons (46 liters).
Fuel selector/shutoff switch on front panel (1/4 turn).
Replaceable fuel filter.

MAXIMUM GROUND SPEEDS:

Forward: 

 8 mph (12.9 km/h)

Reverse: 

 4 mph (6.4 km/h)

WHEELS & TIRES:

Drive wheels:

642211:  23 X 8.50-12 4-Ply Turf Tread Tires

Casters:

  13 X 5.00-6 4-Ply Rib Tread Tires

Pressure:

   14 p.s.i. (1 kg/cm

2

)

BRAKING:

Hayes disc type parking brakes. Spring applied for
overload protection.

SEAT:

High back, foam padded with standard armrests.
Fore and aft adjusters, hinged for easy tilt-up access
to pumps and battery. Prop rod to hold in up position.
Internally mounted seat switch.

SPECIFICATIONS

Содержание 642211

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды