manualshive.com logo in svg

Texmo Industries Taro HCS SJ Series, Инструкция и руководство по эксплуатации

Поделиться
Скачать
Texmo Industries Taro HCS SJ Series Скачать руководство пользователя страница 28

The motors are internally wired and pre-connected with the capacitor leads with two leads 
emerging out from the Terminal Box Cover

Only Phase and Neutral need to be connected to these two leads

In case of clarification, please refer to the Connection Diagram displayed in the inner side of the 
Terminal Box Cover

Connecting the Power Supply

Caution

Observe relevant Electricity Board regulations while powering up the pumpset

Warning

Before connecting the wires to the terminal board, make sure the power supply is 
properly disconnected. Failure to do so may lead to electrical shock, short, or injury 
caused by the unintended starting of the pump

Caution

Do not use damaged cables, power plugs, or loose power outlets. Failure to observe 
this precaution could lead to electrical shock, short circuit or fire

Power cable connection to Jet monoblock

Checking direction of rotation of Jet monoblock pump

Danger

Hazardous voltage will cause death, serious injury, electrocution. 
All electrical work must be performed by an authorised electrician, in 
compliance with local electrical equipment standards and internal 
wiring codes.

OMJP001A

28

2020.01

Содержание Taro HCS SJ Series










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды