TEXIO PU100-7.5, Инструкция по эксплуатации

Страница: 15 / 74

5
3. Vout resistor programming --- 0～100%, 0～5/0～10kΩ full scale, user select. Accuracy and linearity: +/-1% of rated Vout.
4. Iout resistor programming --- 0～100%, 0～5/0～10kΩfull scale, user select. Accuracy and linearity: +/-1.5% of rated Iout.
5. On/off control --- By electrical Voltage: 0～0.6V/2～15V or dry contact, user selectable logic.
6. Output current monitor --- 0～5V or 0～10V, user selectable. Accuracy: 1%.
7. Output voltage monitor --- 0～5V or 0～10V, user selectable. Accuracy: 1%.
8. Power supply OK signal --- 4～5V-OK, 0V-Fail. 500ohm series resistance.
9. Parallel operation --- Possible, up to 4 units in master/slave mode with single wire current balance connection.
10. Series operation --- Possible (with external diodes), up to 2 units.
11. CV/CC indicator --- CV: TTL high (4～5V), source current: 10mA, CC: TTL low (0～0.6V), sink current: 10mA.
12. Enable/Disable --- Dry contact. Open: off, Short: on. Max. voltage at Enable/Disable in: 6V.
13. Local/Remote
analog control
--- By electrical signal or Open/Short: 0～0.6V or short: Remote, 4～5V or open: Local.
14.Local/Remote
Analog status signal.
--- Open collector. Local: Open, Remote: On, Maximum voltage: 30V, maximum sink current: 5mA.
2.6. PROGRAMMING AND READBACK (RS232/485, Optional IEEE Interface) (At the time of 23℃
±5℃)
1. Vout programming accuracy --- 0.1%+0.05% of rated output voltage
2. Iout programming accuracy --- 0.1%+0.15% of rated output current
3. Vout programming resolution --- 0.012% of full scale
4. Iout programming resolution --- 0.012% of full scale
5. Vout readback accuracy --- 0.1%+0.15% of rated output voltage
6. Iout readback accuracy --- 0.1%+0.35% of rated output current
7. Vout readback resolution --- 0.012% of full scale
8. Iout readback resolution --- 0.012% of full scale
2.7. PROTECTIVE FUNCTIONS
V 6 8 12.5 20 30 40 60 80 100 150 300 600
1.Foldback protection -- Output shut-down when power supply change from CV to CC User presetable.
2.Over-voltage protection -- Inverter shut-down, manual reset by AC input recycle or by OUT button.
3.Over-voltage trip point V 0.5～7.5 0.5～10 1～15 1～24 2～36 2～44 5～66 5～88 5～110 5～165 5～330 5～660
4.Output under voltage limit
--
Preset by front panel or communication port. Prevents from adjusting Vout bellow limit.
Raises the PS_OK signal in case of output voltage is bellow limit.
5.Over temperature protection -- User selectable, latched or non latched
2.8. FRONT PANEL
-- Vout/Iout manual adjust by separate encoders (coarse and fine adjustment).
-- OVP/UVL manual adjust by Vout. Adjust encoder.
-- Address selection by Voltage Adjust encoder. No of addresses: 31.
-- Go to local control.
-- Output on/off
-- AC on/off
-- Front panel Lock
-- Foldback control
-- Baud rate selection: 1200, 2400, 4800, 9600, and 19200.
1.Control functions
-- Re-start modes (automatic restart, safe mode).
-- Vout: 4 digits, accuracy: 0.5% of rated output v/-1count. 2.Display
-- Iout: 4 digits, accuracy: 0.5% of rated output c/-1count.
3.Indications -- VOLTAGE, CURRENT, ALARM, FINE, PREVIEW, FOLDBACK, LOCAL, OUTPUT ON.
2.9. ENVIRONMENTAL CONDITIONS
1. Operating temperature -- 0～50℃, 100% load.
2. Storage temperature -- －20～70℃
3. Operating humidity % 30～90% RH (no condensation).
4. Storage humidity % 10～95% RH (no condensation).
5. Altitude
--
Maximum 3000m. Derate output current by 2%/100m above 2000m. Alternatively, derate maximum ambient
temperature by 1℃/100m above 2000m.