manualshive.com logo in svg

Texas Instruments TMS320F28004 Series, Руководство пользователя

Поделиться
Скачать
Texas Instruments TMS320F28004 Series Скачать руководство пользователя страница 19

Advisory

LPM: STANDBY Low-Power Mode is Not Supported

Revisions Affected

0, A, B

Details

The STANDBY low-power mode is not supported.

Workaround

The IDLE or HALT low-power modes can be used for power reduction. See the 

TMS320F28004x Real-Time Microcontrollers Technical Reference Manual

 for information 

on implementing these modes.

If IDLE is used, additional power reduction can be optionally achieved through software by 
one or all of these methods:
• Decrease the SYSCLK frequency:

– Change the SYSCLK source to OSCCLK by configuring SYSPLLCTL1[PLLCLKEN] 

= 0.

– Change the SYSCLKDIVSEL register to a higher divider.

• Disable peripheral clocks through the PCLKCRx register.

www.ti.com

Silicon Revision B Usage Notes and Advisories

SPRZ439G – JANUARY 2017 – REVISED AUGUST 2022

Submit Document Feedback

TMS320F28004x Real-Time MCUs Silicon Errata

Silicon Revisions B, A, 0

19

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320F28004 Series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды