manualshive.com logo in svg

Texas Instruments SM320C6455-EP, Руководство по данным


Поделиться
Скачать
background image

www.ti.com

SM320C6455-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR

SPRS462B – SEPTEMBER 2007 – REVISED JANUARY 2008

software such as Code Composer Studio.

For the PCI host boot, the CPU is out of reset, but it executes an IDLE instruction until a DSP interrupt
is generated by the host. The host can generate a DSP interrupt through the PCI peripheral by setting
the DSPINT bit in the Back-End Application Interrupt Enable Set Register (PCIBINTSET) and the
Status Set Register (PCISTATSET).

Note that the HPI host boot is a hardware boot mode while the PCI host boot is a software boot mode.

If PCI boot is selected, the on-chip bootloader configures the PLL1 Controller such that CLKIN1 is
multiplied by 15. More specifically, PLLM is set to 0Eh (x15) and RATIO is set to 0 (

÷

1) in the PLL1

Multiplier Control Register (PLLM) and PLL1 Pre-Divider Register (PREDIV), respectively. The CLKIN1
frequency must not be greater than 50 MHz so that the maximum speed of the internal ROM, 750
MHz, is not violated. The CFGGP[2:0] pins must be set to 000b during reset for proper operation of the
PCI boot mode.

As mentioned previously, a DSP interrupt must be generated at the end of the host boot process to
begin execution of the loaded application. Because the DSP interrupt generated by the HPI and PCI is
mapped to the EDMA event DSP_EVT (DMA channel 0), it will get recorded in bit 0 of the EDMA
Event Register (ER). This event must be cleared by software before triggering transfers on DMA
channel 0.

•

EMIFA 8 bit ROM boot (BOOTMODE[3:0] = 0100b)

After reset, the device will begin executing software out of an Asynchronous 8 bit ROM located in
EMIFA CE3 space using the default settings in the EMIFA registers. This boot mode is a hardware
boot mode.

•

Master I2C boot (BOOTMODE[3:0] = 0101b)

After reset, the DSP can act as a master to the I2C bus and copy data from an I2C EEPROM or a
device acting as an I2C slave to the DSP using a predefined boot table format. The destination
address and length are contained within the boot table. This boot mode is a software boot mode.

•

Slave I2C boot (BOOTMODE[3:0] = 0110b)

A Slave I2C boot is also implemented, which programs the DSP as an I2C Slave and simply waits for a
Master to send data using a standard boot table format.

Using the Slave I2C boot, a single DSP or a device acting as an I2C Master can simultaneously boot
multiple slave DSPs connected to the same I2C bus. Note that the Master DSP may require booting
via an I2C EEPROM before acting as a Master and booting other DSPs.

The Slave I2C boot is a software boot mode.

•

Serial RapidIO boot (BOOTMODE[3:0] = 1000b through 1111b)

After reset, the following sequence of events occur:
–

The on-chip bootloader configures device registers, including SerDes, and EDMA3

–

The on-chip bootloader resets the peripheral's state machines and registers

–

RapidIO ports send idle control symbols to initialize SerDes ports

–

The host explores the system with RapidIO maintenance packets

–

The host identifies, enumerates, and initializes the RapidIO device

–

The host controller configures DSP peripherals through maintenance packets

–

The application software is sent from the host controller to DSP memory

–

The DSP CPU is awakened by interrupt such as a RapidIO DOORBELL packet

–

The application software is executed and normal operation follows

For Serial RapidIO boot, BOOTMODE2 (L26 pin) is used in conjunction with CFGGP[2:0] (T26, U26,
and U25 pins, respectively) to determine the device address within the RapidIO network.
BOOTMODE2 is the MSB of the address, while CFGGP[2:0] are used as the three LSBs–giving the
user the opportunity to have up to 16 unique device IDs.

BOOTMODE[1:0] (L25 and P26, respectively) denote the configuration of the RapidIO peripheral; i.e.,
"00b" refers to RapidIO Configuration 0. For exact device RapidIO Configurations, see the

TMS320C645xx Bootloader User's Guide

(literature number

SPRUEC6

).

Device Overview

18

Submit Documentation Feedback

Содержание SM320C6455-EP































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SM320C6455-EP

NEC DS1-MP10RX series Operation Manual preview
DS1-MP10RX series
Бренд: NEC Страницы: 39
Bamix SliceSy Instruction Manual preview
SliceSy
Бренд: Bamix Страницы: 48
Da-Lite TENSIONED CONTOUR ELECTROL Instruction Manual preview
TENSIONED CONTOUR ELECTROL
Бренд: Da-Lite Страницы: 8
IEI Technology WAFER-C400EV User Manual preview
WAFER-C400EV
Бренд: IEI Technology Страницы: 45
TECHWOOD TRO-1726 Instruction Manual preview
TRO-1726
Бренд: TECHWOOD Страницы: 16
Ross openGear GPI-8941 Series User Manual preview
openGear GPI-8941 Series
Бренд: Ross Страницы: 92
ninja Kitchen ULTRA PREP PS100 Owner'S Manual preview
ULTRA PREP PS100
Бренд: ninja Kitchen Страницы: 9
MAGIMIX Spiral Expert Manual preview
Spiral Expert
Бренд: MAGIMIX Страницы: 40
Epson ELPMB27 Installation Manual preview
ELPMB27
Бренд: Epson Страницы: 20
Epson ELPIUO3 User Manual preview
ELPIUO3
Бренд: Epson Страницы: 28
Epson ELPHB800 Installation Instructions preview
ELPHB800
Бренд: Epson Страницы: 5
Epson ELPAF58 User Manual preview
ELPAF58
Бренд: Epson Страницы: 2
Epson 26-484-01 Installation Instructions preview
26-484-01
Бренд: Epson Страницы: 5
Epson ELPIU03 Quick Setup Manual preview
ELPIU03
Бренд: Epson Страницы: 2
Epson BrightLink Solo Interactive Module (IU-01 Quick Setup Manual preview
BrightLink Solo Interactive Module (IU-01
Бренд: Epson Страницы: 40
Epson ELPMB24 Installation Manual preview
ELPMB24
Бренд: Epson Страницы: 52
Epson ELPMB27 Product Overview preview
ELPMB27
Бренд: Epson Страницы: 2
Epson PowerLite 450W Brochure & Specs preview
PowerLite 450W
Бренд: Epson Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды