Texas Instruments SimpleLink CC2652RB, Руководство пользователя

Страница: 17 / 70

8.10 Bluetooth Low Energy - Receive (RX) (continued)
When measured on the CC26x2RBEM-7ID reference design with T
c
= 25 °C, V
DDS
= 3.0 V, f
RF
= 2440 MHz with
DC/DC enabled unless otherwise noted. All measurements are performed at the antenna input with a combined RX and TX
path.
All measurements are performed conducted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Frequency error tolerance
Difference between the incoming carrier
frequency and the internally generated carrier
frequency
> (–500 / 500) kHz
Data rate error tolerance
Difference between incoming data rate and the
internally generated data rate (37-byte packets)
> (–700 / 750) ppm
Co-channel rejection
(1)
Wanted signal at –67 dBm, modulated interferer in
channel,
BER = 10
–3
–7 dB
Selectivity, ±2 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at
±2 MHz, Image frequency is at –2 MHz
BER = 10
–3
, measured at input level –70 dBm
8 / 4
(2)
dB
Selectivity, ±4 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at
±4 MHz,
BER = 10
–3
, measured at input level –70 dBm
36 / 36
(2)
dB
Selectivity, ±6 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at
±6 MHz,
BER = 10
–3
, measured at input level –70 dBm
37 / 36
(2)
dB
Selectivity, image frequency
(1)
Wanted signal at –67 dBm, modulated interferer at
image frequency,
BER = 10
–3
, measured at input level –70 dBm
4 dB
Selectivity, image frequency
±2 MHz
(1)
Note that Image fre 2 MHz is the Co-
channel. Wanted signal at –67 dBm, modulated
interferer at ±2 MHz from image frequency, BER =
10
–3
, measured at input level –70 dBm
–7 / 36
(2)
dB
Out-of-band blocking
(3)
30 MHz to 2000 MHz –16 dBm
Out-of-band blocking 2003 MHz to 2399 MHz –21 dBm
Out-of-band blocking 2484 MHz to 2997 MHz –15 dBm
Out-of-band blocking 3000 MHz to 12.75 GHz –12 dBm
Intermodulation
Wanted signal at 2402 MHz, –64 dBm. Two
interferers at 2408 and 2414 MHz respectively, at
the given power level
–38 dBm
(1) Numbers given as I/C dB
(2) X / Y, where X is +N MHz and Y is –N MHz
(3) Excluding one exception at F
wanted
/ 2, per Bluetooth Specification
(4) Suitable for systems targeting compliance with worldwide radio-frequency regulations ETSI EN 300 328 and EN 300 440 Class 2
(Europe), FCC CFR47 Part 15 (US), and ARIB STD-T66 (Japan)
8.11 Bluetooth Low Energy - Transmit (TX)
When measured on the CC26x2RBEM-7ID reference design with T
c
= 25 °C, V
DDS
= 3.0 V, f
RF
= 2440 MHz with
DC/DC enabled unless otherwise noted. All measurements are performed at the antenna input with a combined RX and TX
path.
All measurements are performed conducted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
General Parameters
Max output power
Differential mode, delivered to
a single-ended 50 Ω load
through a balun
Differential mode, delivered to a single-ended 50
Ω load through a balun
5 dBm
Output power
programmable
range
Differential mode, delivered to a single-ended 50 Ω load through a balun 26 dB
www.ti.com
CC2652RB
SWRS232D – FEBRUARY 2019 – REVISED FEBRUARY 2021
Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 17
Product Folder Links: CC2652RB