background image

User’s Guide

ADC364xEVM Evaluation Module

Abstract

This user’s guide describes the characteristics, operation, and use of the ADC364x evaluation module (EVM).
This user's guide discusses how to set up and configure the software and hardware, and reviews various
aspects of the program operation. Throughout this document, the terms evaluation board, evaluation module,
and EVM are synonymous with the ADC364xEVM. In the following sections of this document, the ADC364x
evaluation board is referred to as the EVM and the ADC364x device is referred to as the ADC device.

Table of Contents

Abstract

......................................................................................................................................................................................

1

1 Introduction

.............................................................................................................................................................................

2

2 Equipment

...............................................................................................................................................................................

3

2.1 Evaluation Board Feature Identification Summary.............................................................................................................

3

2.2 Required Equipment..........................................................................................................................................................

4

3 Setup Procedure

.....................................................................................................................................................................

5

3.1 Install High-Speed Data Converter (HSDC) Pro Software.................................................................................................

5

3.2 Install ADC35XXEVM GUI 1.0 Software............................................................................................................................

5

3.3 Connect the ADC EVM and TSW1400EVM.......................................................................................................................

5

3.4 Connect the Power Supply and Mini-USB Connections....................................................................................................

6

4 Device Configuration

..............................................................................................................................................................

7

4.1 Bypass Mode.....................................................................................................................................................................

8

4.2 Real Decimation Mode.....................................................................................................................................................

12

4.3 Complex Decimation Mode..............................................................................................................................................

16

5 External Clocking Hardware Setup

.....................................................................................................................................

20

5.1 Hardware Modfications....................................................................................................................................................

20

5.2 Hardware Setup: Real Decimation 16x Mode..................................................................................................................

24

5.3 External Clock: ADC35XX GUI Real Decimation Mode ..................................................................................................

24

6 ADC364xEVM Power Monitor

..............................................................................................................................................

25

7 Test Pattern

...........................................................................................................................................................................

26

www.ti.com

Abstract

SBAU232 – OCTOBER 2020

Submit Document Feedback

ADC364xEVM Evaluation Module

1

Copyright © 2020 Texas Instruments Incorporated

Содержание ADC364 EVM Series


































Отзывы: