Tesla SOLARGLASS Скачать руководство пользователя | Manualshive

Страница: 15 / 20

background image

15

1551592-00-B

UNDERLAYMENT AND DECK LEVEL FLASHING

Firestone Clad-Gard is a self-adhering underlayment. Mechanical fasteners are

not required under

standard installation conditions, blind nail as necessary. Refer to the manufacturer’s instructions for full

details. First determine the layout direction for underlayment, either Standard or Banded.

Start with a half-width strip at the edge of the roof (eave or rake). Lap a full-width strip 18” to create a
double layer of underlayment. Repeat this fastening and waterproofing process while moving uproof.

1.

Standard Installation

Underlayment may be installed in the standard horizontal orientation, parallel to the eave.

2.

Banded Installation

Underlayment may be installed in the banded orientation, parallel to the rake.

Standard Installation

Banded Installation

«
...
13
14
15
16
17
...
»

Содержание SOLARGLASS





















Отзывы:

Нет отзывов

Похожие инструкции для SOLARGLASS

Бренд: TOPSCCC Technology Страницы: 74

Бренд: VAF instruments Страницы: 36

Бренд: Colormetrics Страницы: 91

Бренд: MEE Страницы: 44

Бренд: UTAS Страницы: 64

MPPC-240T-HW-01

Бренд: Nexcom Страницы: 81

Бренд: ICPDAS Страницы: 8

Бренд: Vimar Страницы: 72

Бренд: IAS Страницы: 6

Бренд: Aaeon Страницы: 62

Бренд: Zennio Страницы: 2

POLARIS II PROFESSIONAL

Бренд: Bartec Страницы: 54

Бренд: C&T Solution Страницы: 36

Бренд: Fagor Страницы: 74

Q.PEAK DUO ML-G11 Series

Бренд: Qcells Страницы: 12

Sunmodule SW xx poly RGA

Бренд: SolarWorld Страницы: 8

Бренд: FREEFORCE Страницы: 7

Q MAXX-G2 Series

Бренд: Q CELLS Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды