background image

14

1551592-00-B

•  Do not handle PV Modules under wet conditions unless wearing appropriate protective equipment.

•  Do not attempt to make an electrical connection with wet, soiled, or otherwise faulty connectors.

•  Do not wear metallic rings, watchbands, earrings, nose rings, lip rings, or other metallic objects while 

installing or troubleshooting PV systems.

•  Do not use a PV Module with broken glass. A damaged PV Module cannot be repaired and must not be 

used.

•  Do not open electrical connections or unplug connectors while the circuit is under load.

• 

Do not use PV Modules near equipment or in places where flammable liquid, gases, or other hazardous 

materials are located.

•  Do not apply paint or adhesive to any module top surface or backsheet.

•  Do not drop PV Modules or allow objects to fall on modules. Do not leave a module unsupported or 

unsecured.

•  Do not disassemble or modify PV Modules in any way. Doing so may degrade performance or cause 

irreparable damage and will void any applicable warranties.

• 

Do not direct artificially concentrated sunlight onto the PV Module.

•  Do not allow children or unauthorized persons near the installation site or storage site of modules.

•  Wear non-slip gloves when carrying PV Modules. Exercise caution when transporting and installing PV 

Modules. 

• 

Do not lift any module by the module’s junction box or electrical leads.

MATERIAL HANDLING

Содержание SOLARGLASS





















Отзывы: