Tescom TC-5922BP Скачать руководство пользователя страница 8

Страница: 8 / 59

Safety Symbols and Terms

viii

Various symbols are used in this manual and on the product itself to ensure correct usage, to prevent

danger to the user and others, and to prevent property damage. The meanings of these symbols are

described below. It is important that you read these descriptions thoroughly and fully understand its

context.

Safety Terms

WARNING:

Identifies conditions or practices that could result in injury or loss of life.

CAUTION:

Identifies conditions or practices that could result in damage to the product or other property.

Symbols:

The following symbols may appear in this manual or on the product.

Symbol

Meaning

 Crush hazard

Moving part can cause serious injury. Must not operate Shield Box when

unauthorized person is in proximity.

Symbol

Meaning

Indicates a potentially hazardous situation which,if not avoided, could result in

serious injury and/or equipment damage.

Indicates a potentially hazardous situation which, if not avoided, may result in a

minor or moderate injury and/or equipment damage. It may also be used to

alert against unsafe practices.

Indicates necessary information or useful information for operation and

maintenance.

Содержание TC-5922BP



























































Результаты поиска

Содержание TC-5922BP

Отзывы:

Tescom TC-5922BP, Руководство пользователя, Страница: 8 / 59

Результаты поиска

Содержание TC-5922BP

Отзывы: