Service and Repair Manual
November 2020
Platform Components
26
Z
®
-45 XC
™
• Z
®
-45 HF
Part No. 1268197GT
6
Move the function enable toggle switch to
either side and hold the platform rotate toggle
switch to the right position until the platform is
fully rotated to the right. Continue holding the
toggle switch until air stops coming out of the
bleed screw. Close the bleed screw.
Crushing hazard. Keep clear of
the platform during rotation.
7
Clean up any oil that may have spilled.
Properly discard the used oil.
8
Rotate the platform fully in both directions and
inspect the bleed screws for leaks.
2-3
Platform Overload System
Proper calibration of the platform overload system
is essential to safe machine operation. Continued
use of an improperly calibrated platform overload
system could result in the system failing to sense
an overloaded platform. The stability of the
machine is compromised, and it could tip over.
Note: Perform this procedure with the machine on
a firm, level surface.
How to Perform a Zero Load
Platform Calibration
Perform this procedure when platform overload is
not operating within the calibration parameters.
This procedure will re-calibrate the zero load point
without affecting a previous full load calibration. In
most cases the machine will maintain full load
capacity, however, in some situations the platform
load capacity may be reduced until a full load
calibration has been performed.
1
Remove all weight, tools, accessories and
equipment from the platform.
Tip-over hazard. Failure to
remove all non-integrated
factory and non-factory options
and accessories could result in
the machine tipping over,
causing death or serious injury.
2
Turn the key switch to ground controls.
Содержание Genie Z-45 XC
