Terex Genie GTH-1256 Скачать руководство пользователя страница 60

Страница: 60 / 136

3-36

GTH-1256

Part No. 1272856

September 2016

Section 3 • Repair Procedures

How to Prime the Hydrostatic
Transmission Pump

WARNING

Bodily injury hazard. This
procedure requires speci

repair skills, lifting equipment
and a suitable workshop.
Attempting this procedure
without these skills and tools
could result in death or serious
injury and signi

cant component

damage. Dealer service is
strongly recommended.

Connect a 0 to 870 psi / 0 to 60 bar pressure
gauge to port TP3 (hydrostatic transmission
boost pressure test port).

Start the engine. Run at low idle for 5 seconds.
Shut the engine off and wait for 15 seconds.

Start the engine. Run at low idle for 10
seconds. Shut the engine off and wait for 15
seconds.

4 Note: Repeat step 4 until the pressure gauge

connected to TP3 reads 290 psi / 20 bar or
greater.

Apply the brake pedal and start the engine.
Shift the transmission into forward and
disengage the emergency brake.

Release the brake pedal and slowly increase
the engine rpm until the machine starts to
move. Apply the brake.

HYDRAULIC PUMPS

Shift the transmission into reverse. Release
the brake pedal and slowly increase the engine
rpm until the machine starts to move. Apply the
brake.

Engage the emergency brake and turn the
engine off. Check for hydraulic leaks.

Содержание Genie GTH-1256









































































































































Результаты поиска

Содержание Genie GTH-1256

Отзывы:

Похожие инструкции для Genie GTH-1256

Бренды по названию

Популярные бренды

Terex Genie GTH-1256, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie GTH-1256

Отзывы:

Похожие инструкции для Genie GTH-1256

Бренды по названию

Популярные бренды