Tennant 5700XPS Скачать руководство пользователя страница 74

Страница: 74 / 84

MAINTENANCE

5700XPS MM402 (6--02)

TRANSPORTING THE MACHINE

1. Position the rear of the machine at the

loading edge of the truck or trailer.

FOR SAFETY: Use truck or trailer that

will support the weight of the machine.

NOTE: Empty the recovery and solution tanks

before transporting the machine.

2. If the loading surface is not horizontal or is

higher than 380 mm (15 in) from the ground,

use a winch to load machine.

If the loading surface is horizontal AND is

380 mm (15 in) or less from the ground, the

machine may be pushed onto the truck or

trailer.

3. To winch the machine onto the truck or

trailer, attach the winching chains to the rear

tie down locations on either side of the

machine frame by the rear casters.

4. Unplug the drive motor from the electrical

harness before attempting to winch the

machine. The machine will become easier to

maneuver when it is unplugged.

FOR SAFETY: When loading machine

onto truck or trailer, use winch. Do not

push the machine onto the truck or

trailer unless the loading surface is

horizontal AND is 380 mm (15 in) or less

from the ground.

5. Position the machine onto the truck or trailer

as far as possible. If the machine starts to

veer off the centerline of the truck or trailer,

stop and straighten the machine.

Содержание 5700XPS





















































































Результаты поиска

Содержание 5700XPS

Отзывы:

Бренды по названию

Популярные бренды

Tennant 5700XPS, Руководство по эксплуатации

Результаты поиска

Содержание 5700XPS

Отзывы:

Бренды по названию

Популярные бренды