Tennant 5700XPS Скачать руководство пользователя страница 15

Страница: 15 / 84

OPERATION

5700XPS MM402 (9--95)

BATTERY DISCHARGE INDICATOR

The battery discharge indicator shows the charge

level of the batteries. It displays the charge level

when the machine is operating.

When the batteries are fully charged, the indicator

on the far right is lit. As the batteries discharge,

the indicator will move along the display to the

left. The batteries should be recharged when the

indicator flashes. The scrub head will raise, and

the vacuum fan and brushes will shut off. The

propel will operate for a short time to allow the

operator to return the machine to the battery

charging area.

NOTE: The reading on the battery discharge

indicator is not accurate when the machine is first

powered on. Operate the machine a few minutes

before reading the charge level of the batteries.

NOTE: The battery discharge indicator will not

reset from the flashing indicator unless the

batteries have been fully charged.

HOURMETER

The hourmeter records the number of hours the

machine has been powered on. This information

is useful when servicing the machine.

ON-OFF KEY SWITCH

The on-off key switch controls machine power

with a key.

On: Turn the key to the right.

Off: Turn the key to the left.

Содержание 5700XPS





















































































Результаты поиска

Содержание 5700XPS

Отзывы:

Бренды по названию

Популярные бренды

Tennant 5700XPS, Руководство по эксплуатации

Результаты поиска

Содержание 5700XPS

Отзывы:

Бренды по названию

Популярные бренды