Tennant 5700XPS Скачать руководство пользователя страница 50

Страница: 50 / 84

MAINTENANCE

5700XPS MM402 (6--02)

NOTE: If the red “ABNORMAL CYCLE” lamp

lights when the TENNANT charger is plugged into

a wall outlet, the charger cannot charge the

battery and there is something wrong with the

battery.

8. The TENNANT charger will start

automatically. When the batteries are fully

charged, the TENNANT charger will

automatically turn off.

9. After the charger has turned off, unplug the

charger from the wall outlet.

10.Unplug the charger connector from the

battery connector on the machine.

FOR SAFETY: When maintaining or

servicing machine, avoid contact with

battery acid.

11. Check the electrolyte level in each battery

cell after charging. If needed, add distilled

water to raise the electrolyte level to about

12 mm (0.4 in) below the bottom of the sight

tubes.

12. Lower the solution tank.

13. Pull up on the support arm and rotate the

stop arm out of the way to allow the solution

tank to close completely.

TOUCH PANEL

The touch panel can be used to run a

self-diagnostic test of the machine electrical

components and system.

1. Turn the machine power off.

2. While pressing the squeegee switch, turn

the machine power on. Continue pressing

the squeegee switch a few seconds, then

release the switch.

07224

Содержание 5700XPS





















































































Результаты поиска

Содержание 5700XPS

Отзывы:

Бренды по названию

Популярные бренды

Tennant 5700XPS, Руководство по эксплуатации

Результаты поиска

Содержание 5700XPS

Отзывы:

Бренды по названию

Популярные бренды