Tennant 5700XPS Скачать руководство пользователя страница 16

Страница: 16 / 84

OPERATION

5700XPS MM402 (3--97)

SQUEEGEE LEVER

The squeegee lever is used when scrubbing to

temporarily lift the squeegee.

Raise squeegee: Pull the lever up, and move it to

the right to lock the lever in the up position.

Lower squeegee: Move the squeegee lever up

and to the left to unlock it, and then release the

lever.

POWER KILL SWITCH (OPTION)

The power kill switch halts all power to the

machine.

Halt: Hit the power kill switch.

Restart: Turn the power kill switch to the right to

release the switch. Turn off the machine power,

then turn on the machine power.

STEERING ADJUSTMENT KNOB

The steering adjustment knob adjusts the

machine steering system to keep the machine

traveling straight.

If the machine pulls to the right, turn the knob to

the left.

If the machine pulls to the left, turn the knob to the

right.

Содержание 5700XPS





















































































Результаты поиска

Содержание 5700XPS

Отзывы:

Бренды по названию

Популярные бренды

Tennant 5700XPS, Руководство по эксплуатации

Результаты поиска

Содержание 5700XPS

Отзывы:

Бренды по названию

Популярные бренды