®
Operation
Operating Instructions
HEAD AND FOOT ADJUSTMENTS (A, B)
UÊ `ÕÃÌÃÊÌ iÊi>`Ê>`ÊÌÊÃiVÌÃÊÌÊÌ iÊ`iÃÀi`Ê
positions. Press until the red LED Signature Light
illuminates and desired position is achieved.
BED “FLAT” BUTTON (C)
UÊ /ÊiÛiÊÌ iÊÀ}Ê-ÞÃÌiÊÌÊÌ iÊ>ÌÊ«ÃÌ]Ê
press until the red LED Signature Light illuminates.
NOTE: The “FLAT” cycle can be interrupted and
cancelled by pressing the head or foot adjustment
buttons (A or B). If the “FLAT” command is not
interrupted, all functions are temporarily disabled for
approximately 30 seconds to allow the Ergo System to
reset after the “FLAT” cycle has been completed.
MEMORY BUTTONS (D)
UÊÊ 9ÕÀÊ/*1,
®
Advanced Ergo System
™
can store up to
four (4) Memory positions.
UÊ /Ê-iÌÊ>ÊiÀÞÊ*ÃÌ\ÊÊ7 iÊÊ`iÃÀi`Ê«ÃÌ]Ê
press and hold Memory button until the LED Signature
Light flashes 3 times to signal Memory position is stored.
UÊ /Ê,iV>Ê>ÊiÀÞÊ*ÃÌ\ÊÊ*ÀiÃÃÊ>`Ê `ÊÌ iÊ
corresponding Memory button until the red LED
Signature Light illuminates.* Do not hold for more than
five (5) seconds, otherwise a new Memory position
could be set. If the LED Signature Light begins to flash,
you are reprogramming the Memory position.
HEAD AND FOOT MASSAGE ADJUSTMENTS (E, F)
UÊ /ÕÀÃÊÊÌ iÊi>`Ê>`ÊÌÊ>ÃÃ>}iÊÕÌÃÊ
(starting at intensity 5 of 10).
UÊ -ÜÞÊVÀi>ÃiÃÊÀÊ`iVÀi>ÃiÃÊ>ÃÃ>}iÊÌiÃÌÞ°Ê
To increase Massage Intensity, press the (+) button.
To decrease Massage Intensity, press the (-) button.
Wireless Remote Control Features
READ ADVISORY INFORMATION IN THE SAFETY PRECAUTIONS SECTION OF THIS GUIDE CAREFULLY BEFORE
USING THIS PRODUCT. THE POTENTIAL FOR ELECTRIC SHOCK EXISTS IF ELECTRICAL COMPONENTS ARE NOT
INSTALLED OR OPERATED PROPERLY.
NOTE: An unintentional touch to any button that does not illuminate the red LED Signature Light on the
wireless remote control will cause the keys to light up without performing the associated function. Press
the appropriate wireless remote control button until the red LED Signature Light illuminates to activate
the desired function. This feature was installed to prevent any undesired movement should the wireless
remote control be dropped, etc.
C. RETURN ALL SECTIONS
TO THE FLAT POSITION
E. INCREASE (+) / REDUCE (-)
MASSAGE INTENSITY ON
HEAD SECTION OF THE BASE
G. STOP ALL MASSAGE FEATURES
B. RAISE (+) / LOWER (-)
FOOT SECTION OF THE BASE
D. PROGRAM UP TO 4
MEMORY POSITIONS
F. INCREASE (+) / REDUCE (-)
MASSAGE INTENSITY ON
FOOT SECTION OF THE BASE
H. SELECT 1 OF 4 MASSAGE
WAVE SPEEDS
MASSAGE STOP (G)
UÊ *ÀiÃÃÊ>`Ê `Ê-/"*ÊLÕÌÌÊÕÌÊÌ iÊÀi`ÊÊ-}>ÌÕÀiÊ} ÌÊ
illuminates and the Massage feature stops. The Massage
feature is designed to automatically shut off after 30 minutes
of continuous use. The unit will reset after 5 minutes, and
the Massage feature will again be available for use.
UÊ 9ÕÊ1-/ÊÃÌ«Ê>ÃÃ>}iÊÌÀÃÊi>V ÊÌiÊLivÀiÊ
switching between wave speeds/types.
WAVE MASSAGE SPEED ADJUSTMENTS (H)
UÊ vÊÌ iÊ>ÃÃ>}iÊvi>ÌÕÀiÊÃÊvv]Ê«ÀiÃÃÊ>ÞÊ7>ÛiÊ-«ii`Ê
button to initiate the Wave Massage feature. Each button
represents the amount of time the massage spends in
each section (head or foot) before switching. If the Wave
Massage feature is already on, you must first stop the
massage by pressing the STOP button (G), and then press
the desired Wave Speed; otherwise the Wave Massage
feature will not start.
NOTE: If the massage motors are operating and
the “FLAT” button (C) is pressed, the massage
motors will stop operating during the lowering
of the Ergo System. To then resume massage
operation, press the Head and/or Foot Massage
Adjustments (E, F) or select a Wave Speed.
ADDITIONAL WIRELESS REMOTE CONTROL FEATURES
UÊ /Ê>`ÊÊÌ iÊÛÃLÌÞÊvÊÌ iÊ7ÀiiÃÃÊ,iÌiÊVÌÀÊÊÜÊ
light environments, the buttons are backlit and will light up
when a button is pressed.
UÊ 9ÕÊ>ÀiÊ>LiÊÌÊVÌÀÊÞÕÀÊÀ}Ê-ÞÃÌiÊÜÌ ÊÌ iÊ7ÀiiÃÃÊ
Remote control without pointing the Wireless Remote
control directly at the receiver (best transmission range is
within 9 feet or 3 meters).
A. RAISE (+) / LOWER (-) HEAD
SECTION OF THE BASE
LED SIGNATURE LIGHT
16
Customer Service: 1–800–979–1457
17
Customer Service: 1–800–979–1457
