Tempstar F9MAE Скачать руководство пользователя

Страница: 34 / 54

INSTALLATION INSTRUCTIONS

Gas Furnace: (F/G)9MAE

440 01 4300 02

Specifications subject to change without notice.

L’apprêt GVS-65 (Purple) et le ciment-solvant GVS-65 doivent

être utilisé avec les Royal Pipe. Système IPEX 636, apprêt

PVC/CPVC, Purple pour évacuation des gaz de combustion et

système IPEX 636(1)t, ciment PVC pour évacuation des gaz

de combustion, coté classe IIA, 65 deg C. doivent être utilisés

avec le système d’évacuation IPEX 636 – Ne pas combiner l

’apprêt et le ciment d’un manufacturier avec un système

d’évacuation d’un manufacturier différent.
Bien suivre les indications du manufacturier lors de l’utilisation de

l’apprêt et du ciment et ne pas utiliser ceux-ci si la date

d’expiration est atteinte.
L’opération sécuritaire, tel que définit par ULC S636, du système

de ventilation est basé sur les instructions d’installation suivantes,

ainsi que l’usage approprié de l’apprêt et ciment. Tout arrët feu et

solin de toit utilisés avec ce système doivent être des matériaux

listés UL. L’acceptation du standard Canadien CAN/CSA B149

est directement relié à l’installation conforme aux instructions ci-

haut mentionnées. Le standard Canadien recommande l’

inspection par un personel qualifié et ce, une fois par année.
Les autoritées ayant juridiction (inspecteurs de gas, inspecteurs

en bâtiments, département des incendies, etc) devraient être

consultées avant l’installation afin de déterminer si un permis est

requis.

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each appliance connec-

ted to the venting system being placed into operation could result in

carbon monoxide poisoning or death.

Failure to follow the steps outlined below for each appliance connec-

ted to the venting system being placed into operation could result in

carbon monoxide poisoning or death.

1. Seal any unused openings in venting system.

2. Inspect the venting system for proper size and hori-

zontal pitch, as required in the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the CSA B149.1 Nat-

ural Gas and Propane Installation Code and these in-

structions. Determine that there is no blockage or re-

striction, leakage, corrosion and other deficiencies,

which could cause an unsafe condition.

3. As far as practical, close all building doors and win-

dows and all doors between the space in which the ap-

pliance(s) connected to the venting system are loc-

ated and other spaces of the building.

4. Close fireplace dampers.

5. Turn on clothes dryers and any appliance not connec-

ted to the venting system. Turn on any exhaust fans,

such as range hoods and bathroom exhausts, so they

are operating at maximum speed. Do not operate a

summer exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the thermostat

so appliance is operating continuously.

7. Test for spillage from draft hood equipped appliances

at the draft hood relief opening after 5 minutes of main

burner operation. Use the flame of a match or candle.

8. If improper venting is observed during any of the

above tests, the venting system must be corrected in

accordance with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54 and/or CSA B149.1 Natural Gas and

Propane Installation Code.

9. After it has been determined that each appliance con-

nected to the venting system properly vents when

tested as outlined above, return doors, windows, ex-

haust fans, fireplace dampers and any other gas

−

fired

burning appliance to their previous conditions of use.

General

If this furnace replaces a furnace that was connected to a vent

system or chimney, the vent or vent connectors of other

remaining appliances may need to be re

−

sized. Vent systems

or vent connectors of other appliances must be sized to the

minimum size as determined using appropriate table found in

the current edition of National Fuel Gas Code NFPA 54/ANSI

−

223.1. In Canada, refer to CAN/CSA

−

B149.1

An abandoned masonry chimney may be used as a raceway

for properly insulated and supported combustion

−

air (when

applicable) and vent pipes. Each furnace must have its own set

of combustion

−

air and vent pipes and be terminated

individually, as shown in

Figure 46

for Direct Vent (2

−

pipe)

system or

Figure 47

for ventilated combustion air option.

A furnace shall not be connected to a chimney flue serving a

separate appliance designed to burn solid fuel.
Other gas appliances with their own venting system may also

use the abandoned chimney as a raceway providing it is

permitted by local code, the current edition of the National Fuel

Gas Code and the vent or liner manufacturer’s installation

instructions. Care must be taken to prevent the exhaust gases

from one appliance from contaminating the combustion air of

other gas appliances.
Do not take combustion air from inside the chimney when using

ventilated combustion air or single pipe vent option.
These furnaces can be vented either as direct vent furnace, or

as ventilated combustion air system. Each type of venting

system is described below. Common venting between

furnaces or other appliances prohibited.

Materials

U.S.A.

Combustion air and vent pipe, fittings, primers, and solvents

must conform to American National Standards Institute (ANSI)

standards and American Society for Testing and Materials

(ASTM) standards. See

Table 13

for approved materials for

use in the U.S.A. This furnace is also CSA approved for venting

with M&G DuraVent

PolyPro

polyproplylene venting

systems.

Canada

Special Venting Requirements for Installations in Canada

Installation in Canada must conform to the requirements of

CAN/CSA B149 code. Vent systems

must

be composed of

pipe, fittings, cements, and primers listed to ULC S636. M&G

DuraVent PolyPro polyproplylene venting systems are ULC

S636 listed.

NOTE

: When using polypropylene venting systems, all venting

materials used, including the vent terminations, must be from
the same manufacturer.

Содержание F9MAE























































Результаты поиска

Содержание F9MAE

Отзывы:

Похожие инструкции для F9MAE

Бренды по названию

Популярные бренды

Tempstar F9MAE, Руководство по установке

Результаты поиска

Содержание F9MAE

Отзывы:

Похожие инструкции для F9MAE

Бренды по названию

Популярные бренды