Tempsens CALsys 1700 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 16

Tempsens CALsys 1700 Скачать руководство пользователя страница 13

12

8. Software Installation

The provided Tempsens software offers possibilities to connect furnace temperature bath and change set
point,maximum time span, view real time graph and evaluate measuring data.

8.1

Installation

Install the calibration software using the installation guide file on CD ROM. After installation of the software; Double
click the application. It willopen the screen of software.

8.2

Parameter in Main Screen

8.2.1

Communication

Communication between the furnace and the software is implemented via a RS-232 cable connected between the
furnace and the PC serial port. This enables the acquisition and recording of data, as well as the transfer of
commands from the software application to the tempsens furnace. Communication can be done by clicking on
connect and select correct COM port address (fig. 1) where furnace is connected. Also user has to select type of
controller version3216 (fig. 2). Then click on CONNECT button. Shown com2 connected successfully. Select 3216
version for P104.

«
...
11
12
13
14
15
...
»

Содержание CALsys 1700

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды