TemperZone OPA 465RKTG-P страница 7 Скачать руководство пользователя

Страница: 7 / 16

- 7 -

NT
R

OL
S

10. CONTROLS

10.1 Modbus Connections

The bridging wires should be screwed to terminals A and B separately and should be long enough to be used as the

bridging cables between the 24 V hot terminal and compressors 1 and 2. If in the event a TZT is not used, they can stay

there and not be of anyone’s concern. If on the other hand a TZT with Modbus is used, the installing contractor will see

the label and wires and then wire them to the 24 volt terminals.

RS485 Terminal on UC6

Lower Board Connections

Serial Card BMS

TZT Controller Installation
If a TZT100 controller is used in Modbus format these cables should be

wired to the following terminals on the low voltage input terminal strip
24V Hot terminal to Comp 1

Comp 1 terminal to Comp 2 terminal
Please disregard this instruction if non Modbus controllers are used.

12V

GND

B-

A-

Содержание OPA 465RKTG-P

















Результаты поиска

Содержание OPA 465RKTG-P

Отзывы:

Похожие инструкции для OPA 465RKTG-P

Бренды по названию

Популярные бренды

TemperZone OPA 465RKTG-P, Установка и обслуживание

Результаты поиска

Содержание OPA 465RKTG-P

Отзывы:

Похожие инструкции для OPA 465RKTG-P

Бренды по названию

Популярные бренды