manualshive.com logo in svg

Teltronics SEB NET-PATH, Инструкция по установке и эксплуатации

Поделиться
Скачать
Teltronics SEB NET-PATH Скачать руководство пользователя страница 69

NET-PATH Installation and Operation Guide

Page 4-11

System Reset 
Button

The recessed Reset button on the back of the NET-PATH resets the microprocessor in 
the NET-PATH and initiates a warm boot. Both warm and cold boots may result in the 
loss of active event data. Data stored in flash memory is not affected.

Tests

Choose the Tests option from the main menu to perform basic tests on the LCD 
display and navigation buttons to verify they are functioning properly. All display 
segments illuminate for the LCD test.

Troubleshooting

Refer to the following troubleshooting aids. Find the symptom that most closely 
matches your situation, and then perform the checks described for that symptom. If 
these steps fail to correct the problem, contact your NOC system administrator for 
technical assistance.

Troubleshooting Incoming Calls

NET-PATH does not answer or is busy.

Possible Cause:

•

The telephone line is inoperative. Verify the telephone line can dial out and 
receive calls. If not, contact your local telephone representative.

•

The NET-PATH is off-hook, trying to place a call. Check the OH indicator on the 
LCD display.

•

Defective telephone cable. Replace cable.

•

Country code not set for International modem. See “Country Code Definitions 
for Multi-Tech Modem Model MT5634SMI” on page 4-6. See “Country Code 
Definitions for Multi-Tech Modem Model MT5656SMI” on page 4-8.

NET-PATH answers (off-hook), but no carrier is detected (DCD is OFF).

Possible Cause:

•

Calling modem is bad. Replace modem.

•

Calling with non-compatible modem. Replace with correct modem.

•

Noisy or bad telephone line. Contact your local telephone representative.

NET-PATH answers, but the database or APP cannot download.

Possible Cause:

•

Noisy or defective telephone line. Contact your local telephone representative.

•

Mismatched database (wrong password/site ID). Verify with Polling and Analy-
sis Center. 

Call terminates before the download completes.

Possible Cause:

•

Noisy or defective telephone line. Contact your local telephone representative.

Содержание SEB NET-PATH



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды