manualshive.com logo in svg

Teltronics SEB NET-PATH, Инструкция по установке и эксплуатации

Поделиться
Скачать
Teltronics SEB NET-PATH Скачать руководство пользователя страница 14

Notices

viii

International 
Modem 
Operation

Using the SEBea in Austria, Belgium, Germany, Spain and Switzerland 

Teltronics is required to provide the following information as a condition of the 
telecommunications conformity to Common Technical Regulation 21 (CTR 21/TBR 
21). You may also be responsible for meeting requirements other than those outlined 
in this document. This SEBea product requires an RJ11 adapter to be installed on 
any line that receives Metering Pulses. Metering pulses are used for billing 
purposes and are normally not present unless requested by the subscriber. The 
subscriber may request the Network Provider to add or remove Metering Pulse 
service. Metering pulses are present on all lines in Switzerland.

TeleAdapt Part number TLFTR (www.TeleAdapt.com) is the metering pulse filter 
recommended by Teltronics.

Using the SEBea in Norway & Spain

This product complies with all of the standard DC voltage requirements as specified 
in the EU standards document CTR 21/TBR 21. However, the SEBea does not meet 
the more unusual requirements for maximum voltage in the loop state, as specified in 
specification EG 201 121 V1.1.1 advisory note NO 02 for Norway and Advisory note 
ES 01 for Spain. In the unlikely event of low loop current, the DC voltage may exceed 
the 7.4 V maximum. If this occurs, the user may experience problems with the 
Central Office recognizing an off-hook condition. This condition could occur in the 
event that the subscriber is at the end of very long telephone lines, which are attached 
to older Central Office equipment.

Modem Configuration Restrictions

The modem used in this product is configured to meet specific country requirements. 
This configuration is in the form of AT command settings sent to the modem prior to 
installation. Changing settings may cause a modem to become non-compliant with 
national telecom requirements in specific countries. 

SEBea factory settings configure the modem for use in North America. If you are 
installing the SEBea in a different country, do not connect the modem to the telephone 
interface until the proper country code is entered though the user interface switches 
on the LCD front panel.

Содержание SEB NET-PATH



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды