manualshive.com logo in svg

Teltronics SEB NET-PATH, Инструкция по установке и эксплуатации

Поделиться
Скачать
Teltronics SEB NET-PATH Скачать руководство пользователя страница 40

Installation

Page 2-16

Power-Up and 
Verification

Apply commercial power to the unit and observe the front panel indicators. After 
several seconds, the Power indicator should illuminate. The unit displays different 
conditions depending on the NET-PATH internal programming. The usual event 
sequence follows.

1

The Status indicator flashes while the unit is initializing 

2

After the unit initializes, the Battery indicator illuminates. This indicator is on 
when the battery is fully charged and flashes when the battery is charging. 

3

The NET-PATH displays the

 

internal device libraries on the bottom line of the 

LCD display as the database loads. The Alarm LED flashes twice – once at the 
beginning of the database loading process and once at the conclusion of the 
process.

4

After a successful power-up, the NET-PATH LCD display panel displays a 
banner, the software Program Update Number (PUN), an off-hook indicator 
(OH: Y/N), and the current date and time.

Figure 2-21 NET-PATH LCD Display

22

The indicators for Power, Battery, and Status illuminate. The battery indicator 
may flash to indicate that the battery is charging.

23

If the Status indicator does not illuminate, the NET-PATH does not have a valid 
database loaded. Contact your network system administrator at the Polling and 
Analysis Center. 

Internal Battery 
Test

To perform an internal battery test

1

Confirm that the internal battery is operating properly.

2

While the unit power is on, unplug the NET-PATH’s power cord.

3

Verify the Status and Battery indicators are on and the Power indicator is off.

4

Restore commercial power to the NET-PATH and verify the Power, Status, and 
Battery indicators are on.

5

The Battery LED flashes to indicate the battery is charging.

Functional 
Verification

Verify that the NET-PATH can receive calls by initiating calls from the Polling and 
Analysis Center. If you can call the NET-PATH, it is ready for operation. Should 
problems occur during the NET-PATH installation, refer to "Troubleshooting"‚ page 
4-11 for troubleshooting procedures. 

If the NET-PATH contains an international modem, you must enter the country code 
before the modem can function. "Country Code Definitions for Multi-Tech Modem 
Model MT5634SMI"‚ page 4-6. 

Содержание SEB NET-PATH



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды