Teltonika FM1110 Скачать руководство пользователя страница 70

Страница: 70 / 76

Minimum

value

Maximum

value

Recommended

value

Goes with (depends on)

parameters

Value

type

-2147483647 2147483647

I/O#1 property parameter (ID=1160)

I/O#1

priority (ID=1161)

I/O#1 High level (ID=1162)

I/O#1 logic operand (ID=1164)

I/O#1 averaging length (ID=1165)

S32

8.7.5

I/O#1 logic operand (ID=1164)

Parameter defines when event is sent: 0 – on range exit, 1 – on range entrance, 2 – both,

3 – monitoring, 4 – hysteresis, 5 – on changes.

Minimal

value

Maximum

value

Recommended

value

Goes with (depends on)

parameters

Value

type

I/O#1 property parameter

(ID=1160)

I/O#1

priority

(ID=1161)

I/O#1 High level (ID=1162)

I/O#1 Low level (ID=1163)

I/O#1 averaging length (ID=1165)

8.7.6

I/O#1 averaging length (ID=1165)

Parameter defines I/O property sample length to average. If no averaging needed default

value is 1.

Minimum

value

Maximum

value

Recommended

value

Goes with (depends on)

parameters

Value

type

2592000

I/O#1 property parameter

(ID=1160)

I/O#1

priority

(ID=1161)

I/O#1 High level (ID=1162)

I/O#1 Low level (ID=1163)

I/O#1 logic operand (ID=1164)

S32

Other I/O property elements can be configured in same logic. All I/O element parameters

are listed in the next table.

Downloaded from

www.Manualslib.com

manuals search engine

Содержание FM1110













































































Результаты поиска

Содержание FM1110

Отзывы:

Бренды по названию

Популярные бренды

Teltonika FM1110, Руководство пользователя

Результаты поиска

Содержание FM1110

Отзывы:

Бренды по названию

Популярные бренды