manualshive.com logo in svg

Teltonika FM1110, Руководство пользователя

Поделиться
Скачать
Teltonika FM1110 Скачать руководство пользователя страница 20

 

 

 

 

 

20 

 

 

 

5

 

OPERATIONAL BASICS 

5.1

 

Operational principals 

FM1110  module  is  designed  to  acquire  records  and  send  them  to  the  server.  Records 

contain  GPS  data  and  I/O  information.  Module  uses  GPS  receiver  to  acquire  GPS  data  and  is 
powered with three data acquire methods: time-based, distance-based and angle-based method. 
Note, that if FM1110 loses connection to GPS satellites,  it continues to make records, however 
coordinate  in  these  records  remains  the  same  (last  known  coordinate).  Method’s  details  are 
described  in  section  5.13.  All  data  is  stored  in flash  memory  and  later  can  be  sent  via  GPRS  or 
SMS. GPRS mode is the most preferred data sending mode. SMS mode is mostly used in areas 
without GPRS coverage or GPRS usage is too expensive.  

GPRS and SMS settings are described in later sections. FM1110 communicates with server 

using special data protocol. Data protocol is described in device protocols documentation.  

FM1110  can  be  managed  by  SMS  commands.  SMS  Command  list  is  described  in  SMS 

COMMAND  LIST  section

. 

Module  configuration  can  be  performed  over  TCP  or  via  SMS. 

Configuration  parameters  and  modes  are  described  in  device  protocols  documentation.  Please 
contact Teltonika sale manager to find out more about protocols documentation purchase. 

5.2

 

Sleep modes 

5.2.1

 

Sleep mode 

FM1110 is able to go to sleep mode after configurable Sleep timeout. This timeout (defined 

period) starts counting when device is in STOP mode. After timeout is reached and all conditions 
for  sleep  mode  are  met,  device  goes  to  sleep  mode

.

  While  in  sleep  mode,  FM1110  turns  GPS 

module off and it is not making new periodic records. Only event records is being recorded with 
last known coordinate and sent to AVL server. As a result power usage decreases allowing saving 
vehicle battery. 

 
FM1110 can enter sleep mode if 

ALL

 of these conditions are met: 

 

FM1110 has to be configured to work in Sleep mode and Sleep timeout is reached; 

 

Device must be synchronized time with GPS satellites; 

 

No movement by movement sensor is detected; 

 

Ignition (DIN1) is off; 

 

USB cable detached; 

 
FM1110 exits sleep mode when if 

ONE

 of following conditions are true: 

 

Movement by movement sensor is detected; 

 

Ignition (DIN1) is turned on; 

 

USB cable is connected; 

5.2.2

 

Deep Sleep mode 

While  in  deep  sleep  mode,  FM1110  sets  GPS  receiver  to  sleep  mode  and  turns  off 

GSM/GPRS  module  (it  is  not  possible  to  wake  up  device  via  SMS).  Despite  records  with  last 
known  coordinate  are being  saved  and  send to AVL  server  (GSM/GPRS module  is turned  on to 
send  data  and  after  that  it  is  turned  off  again),  power  usage  is  decreased  to  save  vehicle’s 

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Содержание FM1110













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды