Teltonika FM1110 Скачать руководство пользователя страница 60

Страница: 60 / 76

8.5.2.2

Min Distance (ID=1551)

This parameter indicates distance in meters in order to acquire new record. Record is

stored when the distance between previous records is greater than parameters value. If value is
0 it means no records by min distance will be saved.

Minimum

value

Maximum

value

Recommended

value

Goes with (depends on)

parameters

Value

type

65535

Min Period (ID=1550)

Min Angle (ID=1552)

GPRS Week Time (ID=1555)

U32

8.5.2.3

Min Angle (ID=1552)

This parameter indicates angle in degrees in order to acquire new record. If angle

difference between last recorded coordinate and current position is greater than defined value,
new record is stored. This parameter is operational, when speed is higher than 10km/h. If value
is 0 it means no records by min angle will be saved.

Minimum

value

Maximum

value

Recommended

value

Goes with (depends on)

parameters

Value

type

180

Min Period (ID=1550)

Min Distance (ID=1551)

GPRS Week Time (ID=1555)

U16

8.5.2.4

Min Saved Records (ID=1553)

This parameter defines minimum number of records in one data packet that can be sent to

server. It has higher priority than Data Send Period (ID=1554).

Minimum

value

Maximum

value

Recommended

value

Goes with (depends on)

parameters

Value

type

255

Min Period (ID=1550)

Min Distance (ID=1551)

Min Angle (ID=1552)

GPRS Week Time (ID=1555)

8.5.2.5

Send Period (ID=1554)

This parameter indicates frequency (time interval in seconds) of sending data to server.

Minimum

value

Maximum

value

Recommended

value

Goes with (depends on)

parameters

Value

type

2592000

GPRS Week Time (ID=1545)

U32

8.5.2.6

GPRS Week Time (ID=1555)

Read 8.5.1.4.

8.5.3

Roaming Network GSM operator code “Vehicle on STOP” parameters

8.5.3.1

Min Period (ID=1560)

This parameter indicates time interval in seconds in order to acquire new record. If value is

0 it means no records by min period will be saved.

Minimum

Maximum

Recommended

Goes with (depends on)

Value

Downloaded from

www.Manualslib.com

manuals search engine

Содержание FM1110













































































Результаты поиска

Содержание FM1110

Отзывы:

Бренды по названию

Популярные бренды

Teltonika FM1110, Руководство пользователя

Результаты поиска

Содержание FM1110

Отзывы:

Бренды по названию

Популярные бренды