background image

31 

 

QR code for mobile app registration: 

After installing the mobile application, you can associate the mobile app with the 

ecoLINE PRO

 

device by reading this QR code in the mobile application and entering the registration password 
configured here. You can associate up to 20 mobile devices with the 

ecoLINE PRO

If  a  mobile  application  is  registered,  the  device  can  send  Push  messages  to  the  given  mobile 
device about events generated by its own inputs, and about reports received from the connected 
alarm system, and the device’s output can also be controlled in the mobile app. 

Mobile app registration password

: the registration password configured here has to be provided 

in the mobile application when you wish to associate it with the device. The registration password 
length is 4 to 8 characters and only letters and numbers are accepted. Accented letters are not 
accepted. 

Enable/disable Push notifications

:

 

Push  notification  settings  apply  to  all  registered  mobile  devices  at  the  same  time.  Notifications 
enabled  here  can  be  further  enabled  or  disabled  by  users  on  each  mobile  device  on  demand. 
The device will not send notifications to mobile devices on event categories which are disabled. 

Alarm  system  arming/disarming

:  enable  Push  message  sending  to  the  registered  mobile 

devices about arming/disarming events of the alarm system connected to the device.

 

Alarm  system  alarm  events

:  enable  Push message  sending  to  the  registered mobile  devices 

about alarm events of the alarm system connected to the device.

 

Other  alarm  system  events

:  enable  Push  message  sending  to  the  registered  mobile  devices 

about other events (e.g. failures) of the alarm system connected to the device.

 

Input  events

:  enable  Push  message  sending  to  the  registered  mobile  devices  about  events 

generated by the contact inputs of the device. The message text for each input can be configured 
in the mobile application.

 

Forward  incoming  SMS  messages

:  if  this  option  is  enabled,  the  device  will  forward  SMS 

messages  received  by  its  SIM  card  (e.g.  balance  information  received  from  the  GSM  service 
provider,  in  case  of  pre-pay  card)  to  the  registered  mobile  devices  in  Push  messages. 
The received SMS messages are deleted automatically after forwarding. If this option is disabled, 
the device will delete all SMS messages received by its SIM card without forwarding.

 

Registered mobile devices, and notifications enabled in the mobile application

:

 

Mobile devices associated with the 

ecoLINE PRO

 device are listed in this table. 

Mobile device

: in this field the name of an already registered mobile device is shown, which is 

read by the mobile application directly from the mobile device. 

User name

: the name provided by the user upon registering the mobile application.

 

Alarm  system  arming/disarming

:  the  checkbox  in  this  column  shows  whether  the  user  has 

enabled on the given mobile device reception of notifications about 

the connected alarm system’s 

arming/disarming events.

 

Alarm system alarm events

: the checkbox in this column shows whether the user has enabled 

on the given mobile device reception of notifications abo

ut the connected alarm system’s alarm 

events.

 

Other alarm system events

: the checkbox in this column shows whether the user has enabled 

on the given mobile device reception of notifications about the connected alarm system’s other 
events (e.g. failures).

 

 

 

Содержание ecoLINE PRO





























































Отзывы: