Telit Wireless Solutions UE866-EU Скачать руководство пользователя страница 8

Страница: 8 / 70

UE866 HARDWARE USER GUIDE

1vv0301157 Rev.12

•

2017-02-10

8 of 70

INTRODUCTION

1.1

Scope

The aim of this document is the description of some hardware solutions useful for developing a product
with the Telit UE866 module.

1.2

Audience

This document is intended for Telit customers, who are integrators, about to implement their applications
using our UE866 modules.

1.3

Contact Information, Support

For general contact, technical support services, technical questions and report documentation errors

contact Telit Technical Support at:

[email protected]

Alternatively, use:

http://www.telit.com/support

For detailed information about where you can buy the Telit modules or for recommendations on

accessories and components visit:

http://www.telit.com

Our aim is to make this guide as helpful as possible. Keep us informed of your comments and

suggestions for improvements.

Telit appreciates feedback from the users of our information.

Содержание UE866-EU





































































Результаты поиска

Содержание UE866-EU

Отзывы:

Похожие инструкции для UE866-EU

Бренды по названию

Популярные бренды

Telit Wireless Solutions UE866-EU, Руководство пользователя по оборудованию

Результаты поиска

Содержание UE866-EU

Отзывы:

Похожие инструкции для UE866-EU

Бренды по названию

Популярные бренды