Telit Wireless Solutions UE866-EU Скачать руководство пользователя страница 33

Страница: 33 / 70

UE866 HARDWARE USER GUIDE

1vv0301157 Rev.12

•

2017-02-10

33 of 70

5.5

Communication ports

USB 2.0 HS

The UE866 includes one integrated universal serial bus (USB 2.0 HS) transceiver.

The following table is listing the available signals:

PAD

Signal

I/O

Function

Type

NOTE

USB_D+

I/O

USB differential Data (+)

3.3V

USB_D-

I/O

USB differential Data (-)

3.3V

VUSB

Power sense for the internal USB
transceiver.

Accepted range:
4.4V to 5.25V

The USB_DPLUS and USB_DMINUS signals have a clock rate of 480 MHz.

The signal traces should be routed carefully. Trace lengths, number of vias and capacitive loading

should be minimized. The characteristic impedance value should be as close as possible to 90 Ohms

differential.

In case there is a need to add an ESD protection, the suggested connection is the following:

NOTE:

VUSB pin should be disconnected before activating the Power Saving Mode.

Содержание UE866-EU





































































Результаты поиска

Содержание UE866-EU

Отзывы:

Похожие инструкции для UE866-EU

Бренды по названию

Популярные бренды

Telit Wireless Solutions UE866-EU, Руководство пользователя по оборудованию

Результаты поиска

Содержание UE866-EU

Отзывы:

Похожие инструкции для UE866-EU

Бренды по названию

Популярные бренды