manualshive.com logo in svg

Telit Wireless Solutions GE863-GPS, Руководство пользователя программного обеспечения, Страница: 97 / 109

Поделиться
Скачать
Telit Wireless Solutions GE863-GPS Скачать руководство пользователя страница 97

 
 
 
 

 

 

 

GE863-GPS Software User Guide 

 1vv0300724  Rev. 2 - 24/01/07    

  

5.4.4 GSV - GNSS Satellites in View 

 

This sentence reports the number of satellites (SV) in view, satellite ID numbers, elevation, azimuth 
and SNR value. 
There could be four satellites information per transmission so, if the number of satellites in view is 
bigger, separated GSV sentences will be generated. The number of sentence in transmission and the 
total to be transmitted is shown in the first 2 fields of the sentence.  
 
Table G contains the values for the following example: 
 

$GPGSV,2,1,07,07,79,048,42,02,51,062,43,26,36,256,42,27,27,138,42*71 

$GPGSV,2,2,07,09,23,313,42,04,19,159,41,15,12,041,42*41 

 
 

Table G: GSV Data Format 

Name

 

Example

 

Units

 

Description

 

Message ID 

$GPGSV   

GSV protocol header 

Number of 
Messages 

2 

 

Range 1 to 3 

Message 
Number1 

1 

 

Range 1 to 3 

Satellites in 
View 

07 

 

 

Satellite ID 

07 

 

Channel 1 (Range 1 to 32) 

Elevation 

79 

degrees

 

Azimuth 

048 

degrees

 

SNR (C/No) 

42 

dBHz 

 

.... 

.... 

.... 

 

Satellite ID 

27 

 

Channel 4 (Range 1 to 32) 

Elevation 

27 

degrees

Channel 4 (Maximum 90) 

Azimuth 

138 

degrees

Channel 4 (True, Range 0 to 359) 

SNR (C/No) 

42 

dBHz 

Range 0 to 99, null when not tracking 

Checksum 

*71 

 

 

<CR> <LF> 

 

 

End of message termination 

 

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved 

 

page 97 of 109 

 

Содержание GE863-GPS














































































































Отзывы:

Нет отзывов