Telit Wireless Solutions GE863-GPS Скачать руководство пользователя страница 23

Страница: 23 / 109

GE863-GPS Software User Guide

1vv0300724 Rev. 2 - 24/01/07

1 - microphone muted

NOTE: The mute setting is different from Volume setting: it refers to both the audio paths, the
mute setting will remain even when changing audio path.

2.6.2 Phone number dialing

2.6.2.1 Dial a given phone number

•

Send command

ATD <PhoneNumber><cr>

where:
<PhoneNumber> is the phone number to be dialed

•

wait

for

response:

Response

Reason

Action

The call has been placed

Wait for the other party to lift
the receiver..

BUSY

The line called is busy

retry later

NO ANSWER

The receiver did not answer the
call

retry later

NO CARRIER

Call placing has not been
successful

check for mobile registration
and signal strength

For example:
1- Let's assume you have to call the national number 040 - 4192111,

command:

ATD 0404192111<cr>

response

2- Let's assume you have to call the national number but in international 39-40-4192111,

command:

ATD +39404192111<cr>

response

3- Let's assume you have to call the international 386-40-4192111 without previously setting
the +FCLASS=8 (voice),

command:

ATD +386404192111;<cr>

response

page 23 of 109

Содержание GE863-GPS














































































































Результаты поиска

Содержание GE863-GPS

Отзывы:

Telit Wireless Solutions GE863-GPS, Руководство пользователя программного обеспечения, Страница: 23 / 109

Результаты поиска

Содержание GE863-GPS

Отзывы: