Telit Wireless Solutions GE863-GPS Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 109

Telit Wireless Solutions GE863-GPS Скачать руководство пользователя страница 91

GE863-GPS Software User Guide

1vv0300724 Rev. 2 - 24/01/07

5 GPS operations

5.1 Introduction

The GE863-GPS module is equipped with a SiRFStar III GPS receiver that is controllable by the GSM
modem using a setof AT commands or dedicated NMEA sentences.

5.2 GE863-GPS Serial Ports

4 serial ports are available on the module:

•

•

•

•

MODEM SERIAL PORT
MODEM SERIAL PORT 2 (GPS CONTROL PORT)
GPS SERIAL PORT A (SIRF BINARY)
GPS SERIAL PORT B (NMEA)

5.2.1 GPS SERIAL PORT A (SIRF BINARY)

This port is carrying out the GPS navigation data in SIRF BINARY format.

The default configuration is 57600 bps, 8, n, 1

It is available on the following pins:

PIN #

NAME

DESCRIPTION

TYPE

78

RX_GPS_BIN

GPS RX Data (Sirf Binary)

CMOS 2.8V

80

TX_GPS_BIN

GPS TX Data (Sirf Binary)

CMOS 2.8V

The typical integration requires connecting this pins to MODEM serial port 2.

5.2.2 GPS SERIAL PORT B (NMEA)

This port is carrying out the GPS navigation data in NMEA 0183 format.

The default configuration is 4800 bps, 8, n, 1

It is available on the following pins:

PIN #

NAME

DESCRIPTION

TYPE

68

TX_GPS

GPS TX Data (NMEA)

CMOS 2.8V

73

RX_GPS

GPS RX Data (NMEA)

CMOS 2.8V

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved

page 91 of 109

«
...
89
90
91
92
93
...
»

Содержание GE863-GPS














































































































Отзывы:

Нет отзывов