Telit Wireless Solutions GE863-GPS Скачать руководство пользователя страница 31

Страница: 31 / 109

GE863-GPS Software User Guide

1vv0300724 Rev. 2 - 24/01/07

3.1.1.1 Selecting PB storage active

•

Send command

AT+CPBS=<PB><cr>

where:
<PB> is the desired PB storage:

SM – SIM phonebook
FD – fixed dialing phonebook
LD – last dialed calls list
MC – missed calls list
RC – received calls list

•

wait for response:

Response

Reason

Action

selected PB is now active

Proceed ahead

ERROR

some error occurred

Enable extended result codes
(see par. 2.5.2.1)
and retry.

+CME ERROR: 10

SIM not present

Check SIM or require SIM
insertion and repeat from par.
2.5.2.2

+CMS ERROR: 310

SIM not present

Check SIM or require SIM
insertion and repeat from par.
2.5.2.2

+CME ERROR: 11

SIM is present and PIN is
required to continue operations

insert SIM PIN (see par.
2.5.2.3)

+CMS ERROR: 311

SIM is present and PIN is
required to continue operations

insert SIM PIN (see par.
2.5.2.3)

+CME ERROR: 12

SIM is present and PUK is
required to continue operations

insert SIM PUK (see
par.2.5.2.4)

+CMS ERROR: 316

SIM is present and PUK is
required to continue operations

insert SIM PUK (see
par.2.5.2.4)

+CME ERROR: 13

SIM defect

Check SIM insertion or require
a new SIM not defected and
repeat from par. 2.5.2.2

+CMS ERROR: 313

SIM defect

Check SIM insertion or require
a new SIM not defected and
repeat from par. 2.5.2.2

+CME ERROR: 14

SIM is busy

retry later

+CMS ERROR: 314

SIM is busy

retry later

+CME ERROR: 15

SIM is wrong type

Check SIM, it must be a GSM
SIM.

+CMS ERROR: 315

SIM is wrong type

Check SIM, it must be a GSM

page 31 of 109

Содержание GE863-GPS














































































































Результаты поиска

Содержание GE863-GPS

Отзывы:

Telit Wireless Solutions GE863-GPS, Руководство пользователя программного обеспечения, Страница: 31 / 109

Результаты поиска

Содержание GE863-GPS

Отзывы: