Telex TDI Скачать руководство пользователя страница 20

Страница: 20 / 22

Audio Alignment Procedure

Audio alignment

is done in two steps. First the Rx path is aligned, then the Tx path. The IP-223 has front panel alignment

features for both Rx and Tx. Using the front panel buttons on the IP-223, press and hold the

LINE

button, then press the

button.

While continuing to hold the LINE, repeated presses of the IC button steps through several features, including the alignment
features.

LINE/IC first press:

IP and Subnet mask addresses.

LINE/IC second press:

Tx Alignment tone

LINE/IC third press:

Receive audio signal levels are measured at the DSP level.

LINE/IC fourth press:

Resets screen to normal mode.

General Gain Setup Window

The

General Gain Setup

window is used to set receive and transmit levels for the line.

Set the audio Rx level to

0db

and the Tx audio level to

-22.5dB

for the line. See Figure 16.

Receive Audio Alignment

Enter the

Receive alignment

mode on the IP-223 by pressing and holding the

LINE

button, then successively pressing and

releasing the

button three (3) times. The TDI must be connected to a live PSTN phone line and then taken offhook. This

can be done with C-Soft, or any IP-based Telex Console.

The following steps outline the TDI Rx alignment procedure:

Step 1

From the console, take the telco line offhook. A dial tone should be present.

Step 2

From the front panel Rx control, adjust the dial tone levels to -12dB.

Step 3

Place the telco line back onhook.

FIGURE 16.

General Gain Setup Window

Содержание TDI























Результаты поиска

Содержание TDI

Отзывы:

Бренды по названию

Популярные бренды

Telex TDI, Техническое руководство

Результаты поиска

Содержание TDI

Отзывы:

Бренды по названию

Популярные бренды