manualshive.com logo in svg

Telex TDI, Техническое руководство

Поделиться
Скачать
Telex TDI Скачать руководство пользователя страница 17

17

Audio Level Setup

There are no internal jumpers or adjustments inside the TDI enclosure. Advanced circuitry and DSP software algorithms react 
to changing telephone line impedances resulting in minimal user setup. Each audio input to the TDI (Telco RX and IP-223 
TX) is routed through a complex AGC circuit that provides 44dB of dynamic range control. A nominal 0dB input level applied 
to each of the audio inputs results in ±22dB of dynamic input range control by the TDI.

The TDI audio outputs (Telco TX and IP-223 RX) are derived from the processed audio level and DSP echo canceling 
algorithms to produce nominal 0dB telco and IP-223 levels. The IP-223 system gains are typically set to 0dB (depending on 
system requirements). Figure 11 shows the IP-223 General Gain Setup page where the receive and transmit gains for each line 
are set.

Version 2.000 allows the user to set the system gains. The TDI is initially programmed with the following default parameters:

Ring cadence - 

Ring on = 2000ms, Ring off = 4000ms (United States)

TDI Rx gain - 

+9dB

TDI Tx gain - 

+3dB

FIGURE 11.

General Gain Setup Window—Line Gain Setup Section

Содержание TDI























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды