manualshive.com logo in svg

Telex TDI, Техническое руководство

Поделиться
Скачать
Telex TDI Скачать руководство пользователя страница 13

13

CHAPTER 2

Installation

IP-223 Web Page Configuration

Multicast Address Setup Page

To operate with the TDI, the IP-223 must be initially set to Phone mode from the Multicast Address Setup page, as shown in 
Figure 4.

NOTE:

•

Phone Mode os only available in IP-223 software version 1.08 or higher.

•

TDI configuration is only available in IP-223 software version 4.100 or higher.

•

Caller ID demodulation is only available in IP-223 software version 1.10 or higher.

•

User-selected ring cadence and TDI gain options are only available in TDI firmware version 2.000 and IP-223 
firmware version 4.300 or later.

Each line has a drop down menu that allows selection of the Phone Mode. The Multicast Address and port numbers are 
configured just as any other mode. In Phone Mode, the Multicast Address is not required, as the console connects via TCP/IP. 
Make sure the Rx and Tx port numbers are unique. The ringing signal is broadcast on a unique Multicast Address. The ringing 
signal address must be common to all listening IP-223s and consoles. For console configuration information, please refer to 
the specific user manual for the product.

Содержание TDI























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды