TLV-300E/TAV-900A Professional Digital TV Receiver
User’s Manual
If you were watching video with composite video, use CONFIG/SUB/SOURCE and select RF-IN1 and use
CONFIG/SUB/TUNE CH (tune by channel). The receiver will choose RF-IN1 source for SUB decoder and
tune to the desired channel.
After you tune to the RF signal and exit to the no menu state1, the receiver does not get proper incoming
video signal or setting, then “UNLOCK” message will be shown on the alphanumeric display. If the display
shows some irregular static, video noise, or black screen, make sure your incoming signal quality.
Example) No menu state1 (INPUT PORT STATUS), R1:L indicates RF input-1 is in LOCK state.
.
3 2 . 9
I
F
-
N 1
-
B
d
:
4
B
-
B
0
B
x
B
1
0
C
8
L
-
:
O
8
K
-
1
0
:
-
B
3
:
2
:
B
R
V
-
:
5
0
S
>
< >
R
:
L
2
-
R 1 :
Example) No menu state1 (INPUT PORT STATUS), R1:- indicates RF input-1 is in NO LOCK state.
I
F
-
N 1
-
B
:
4
B
-
B
B
1
L
U
-
:
N
K
O C
:
-
B
3
:
2
:
R
-
:
5
>
< >
R
:
-
2
-
R 1 :
2.8 V
ERIFYING
A
NALOG
A
UDIO
O
UTPUT
Prepare your audio amplifier. You may use any audio amplifier with a stereo line input port.
Look at the rear panel of the receiver and locate the stereo audio output. Connect the output on the back panel
to the input of your audio amplifier.
Analog audio output for MAIN channel (YPbPr/RGBHV/SDI) video is available from L1, R1 connector and
Analog audio output for SUB channel (composite) video is available from L2, R2 connector in the rear panel.
NOTE) If digital audio is set to COMPRESSED mode, analog audio is disabled. Please set the digital audio
to PCM mode in order to enable the analog audio.
2.9 U
SING
DVB-ASI
OR
SMPTE-310M TS O
UTPUT
Attach coaxial cable into BNC OUT(AES3/ASI/SMPTE-310M)-1 connector in the rear panel.
Use CONFIG/BNC OUT(AES/ASI/SMPTE310M)/BNC-1 menu to select DVB-ASI or SMPTE-310M. If the
input signal is not from 8VSB or SMPTE-310M, the SMPTE-310M selection is not possible.
You may use BNC OUT(AES3/ASI/SMPTE-310M)-2~4 as well and use CONFIG/BNC
OUT(AES/ASI/SMPTE310M)/BNC-2~4 menu to select DVB-ASI or SMPTE-310M.
2.10 U
SING
D
IGITAL
A
UDIO
O
UTPUT
Prepare your digital audio amplifier.
Look at the rear panel of the receiver and locate the BNC OUT(AES3/ASI/SMPTE310M) - 1 and 2
connectors. Connect the output on the back panel to the input of your digital audio receiver.
Use CONFIG/BNC OUT(AES/ASI/SMPTE310M)/BNC-1 menu to select MAIN-AES3 to choose audio for
MAIN video.
Use CONFIG/BNC OUT(AES/ASI/SMPTE310)/BNC-1 menu to select SUB-AES3 to choose audio for
Version 2.0
25
