Televic Aladdin Скачать руководство пользователя страница 60

Страница: 60 / 72

Aladdin Digital Infrared Language Distribution

Installation and User Manual

Televic Conference Systems

2011-09-01

6.3.

Charging Procedure

The charging procedure goes as follows:

Connect power core

Switch on

Insert receiver

Receiver charging indicator lights up

LED Status

Charging Status

Charging completed

Blinking

Charging

Off

Charger power of or receiver not

inserted properly.

Note:

Pull out headphone before charging

receiver.

Switch on the charger before inserting

receiver.

Inserting

and

removing

receiver when the charger is powered

on will not damage the receiver.

To maintain the service life of Ni-MH

battery, please charge it for 24 hours

before first service (until charging

indicator keeps lighting).

The charger supplies fast charge during

the first 10 minutes after inserting the

receiver. So please do not frequently

insert and remove receiver to protect

the battery pack.

Continuously charging will not damage

the receiver or the battery pack.

It will result in low battery and may

damage the battery pack if the battery

pack is not used for a long time. Please

fully charge the battery for every three

months.

Please check the battery pack regularly

every 3 years whether the battery pack

is leaking or not. If any leakage or

corrosion is founded, please replace the

battery pack. Please use Aladdin BP

only. The battery pack should be

replaced at least every 5 years.

Содержание Aladdin









































































Результаты поиска

Содержание Aladdin

Отзывы:

Похожие инструкции для Aladdin

Бренды по названию

Популярные бренды

Televic Aladdin, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Aladdin

Отзывы:

Похожие инструкции для Aladdin

Бренды по названию

Популярные бренды