background image

GUaranTee

During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any 

defective  product  when  it  is  returned  to  the  factory. All  parts  replaced  and/or  repaired  shall  be 

covered for the remainder of the original guarantee, or for ninety (90) days, whichever period is 

longer. The original purchaser shall immediately send manufacturer a written notice of the defective 

parts  or  workmanship,  which  written  notice  must  in  all  cases  be  received  prior  to  expiry  of  the 

guarantee.

inTernaTiOnaL GUaranTee

Foreign customers shall enjoy the same guarantee rights as those enjoyed by any customer in 

Bulgaria, except that manufacturer shall not be liable for any related customs duties, taxes or VAT, 

which may be payable.

GUaranTee PrOCeDUre

This guarantee will be granted when the appliance in question is returned. The manufacturer shall 

accept no product whatsoever, of which no prior notice has been received.

COnDiTiOns FOr WaiVinG THe GUaranTee

This  guarantee  shall  apply  to  defects  in  products  resulting  only  from  improper  materials  or 

workmanship, related to its normal use. It shall not cover:

§ Damages resulting from improper transportation and handling;

§ Damages caused by natural calamities, such as fire, floods, storms, earthquakes or lightning;

§ Damages caused by incorrect voltage, accidental breakage or water; beyond the control of the 

manufacturer;

§ Damages caused by unauthorized system incorporation, changes, modifications or surrounding 

objects;

§ Damages caused by peripheral appliances unless such peripheral appliances have been supplied 

by the manufacturer;

§ Defects caused by inappropriate surrounding of installed products;

§ Damages caused by failure to use the product for its normal purpose; 

§ Damages caused by improper maintenance;

§ Damages resulting from any other cause, bad maintenance or product misuse.
In the case of a reasonable number of unsuccessful attempts to repair the product, covered by 

this guarantee, the manufacturer’s liability shall be limited to the replacement of the product as the 

sole compensation for breach of the guarantee. Under no circumstances shall the manufacturer be 

liable for any special, accidental or consequential damages, on the grounds of breach of guarantee, 

breach of agreement, negligence, or any other legal notion.

WaiVer

This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other 

guarantees,  explicit  or  implicit  (including  any  implicit  guarantees  on  behalf  of  the  dealer,  or 

adaptability to specific purposes), and over any other responsibilities or liabilities on behalf of the 

manufacturer. The manufacturer does neither agree, nor empower, any person, acting on his own 

behalf, to modify or alter this Guarantee, nor to replace it with another guarantee, or another liability 

with regard to this product.

UnWarranTeD serViCes 

The manufacturer shall repair or replace unwarranted products, which have been returned to its 

factory, at its sole discretion under the conditions below. The manufacturer shall accept no products 

for which no prior notice has been received.

The  products,  which  the  manufacturer  deems  repairable,  will  be  repaired  and  returned.  The 

manufacturer has prepared a price list and those products, which can be repaired, shall be paid for 

every repaired appliance.

The  closest  equivalent  product,  available  at  the  time,  shall  replace  the  products  manufacturer 

deems irreparable. The current market price shall be charged for every replaced product.

Содержание TP2000





































Отзывы: