Teledyne TIENet 301 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 30

Teledyne TIENet 301 Скачать руководство пользователя страница 7

v

TIENet

®

301 pH/Temperature Device

Table of Contents

Section 1 Introduction

1.1 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.2 Design  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-2
1.3 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-3
1.4 Replacement Parts and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-4

1.4.1 TIENet 301 Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Section 2 Installation and Setup for Signature

2.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.1.1 Connecting the Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-1
2.1.2 Connecting to Signature Portable via a TIENet Receptacle  . . . . . . . . . . . .  2-5
2.1.3 pH Probe Installation Considerations   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-6
2.1.4 Mounting the pH Probe in the Stream  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-6

2.2 Configuring the 301. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

2.2.1 Updating the Device List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

2.3 pH Probe Life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2.4 pH Probe Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

2.4.1 Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2.4.2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

2.5 Firmware Updates  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-12
2.6 Probe Storage and Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-12
2.7 Contact Teledyne Isco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-12

Appendix A Replacement Parts

A.1 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

A.1.1 301 pH Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

List of Figures

1-1 Signature Flow Meter w/ Model 301 TIENet device and pH probe . . . . . . . . . . . .  1-1
2-1 TIENet Device terminal strips   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-1
2-2 Installing cable with a cord-grip fitting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-2
2-3 TIENet Device terminal connections   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-3
2-4 Attach wired terminal strip to case board socket . . . . . . . . . . . . . . . . . . . . . . . . . .  2-3
2-5 Position and secure the cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-4
2-6 How to connect a TIENet plug to the Signature Portable  . . . . . . . . . . . . . . . . . . .  2-5
2-7 Attaching the probe to the carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-7
2-8 Character grid   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-8
2-9 Menu Tree: 301 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-9
2-10 301 Calibration sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-11

«
...
5
6
7
8
9
...
»

Содержание TIENet 301































Отзывы:

Нет отзывов